Tài liệu Operational Administration Recovery and Security ppt

... ID, and all users listed on the accgrp line in the /etc/group file will have read, write, and execute access to the accshared directory. 628 Chapter 11: Operational Administration Recovery and Security CertPrs8 ... screen 650 Chapter 11: Operational Administration Recovery and Security CertPrs8 / RHCE Red Hat Certified Engineer Linux Study Guide / Jang / 222485-1 / Cha...

Ngày tải lên: 11/12/2013, 00:15

... cables or fiber optic strands. All these media have their band limitation, copper have the lowest. So we need lots of links and this is again impractical in terms of costs and some time impossible ... multiplexed together (5x48 kHz = 240 kHz Bandwidth) • Mastergroup - 10 supergroups multiplexed together (10x240 kHz = 2400 kHz Bandwidth) • Other standards also exists - up to 230000 voi...

Ngày tải lên: 10/12/2013, 08:15

... will discuss next. You may take this blueprint and deployment plan and use it as a template for your own project, expanding or cutting and pasting to and from it as you need, or just use the examples ... enterprise administration as opposed to being gatekeepers (see Chapters 2 and 7). To extend security policy over groups and users, you place them into OUs. OUs are themselves...

Ngày tải lên: 10/12/2013, 16:15

... administrators to better understand their security settings and network usage. 24 Module 8: Monitoring and Reporting Traffic and Utilization Reports Traffic and utilization reports display ... network capacity and determine bandwidth policies. Traffic and utilization reports combine data from the Web Proxy service logs and the Firewall service logs. Security Reports...

Ngày tải lên: 10/12/2013, 22:15

... client and connect to ftp.cisco.com. Use your CCO username and password. Step 2 Enter the command cd /cisco/web/tftp and use the ls command to view the directory contents. Step 3 Use the get command ... address, server, and file commands, and then enter the tftp command to start the download. The commands are as follows: a. If needed, use a question mark ( ? ) or enter the help comm...

Ngày tải lên: 11/12/2013, 13:15

... the last is 2016, and the Aux port is 2017. If you forget, type in "show line" at the router command prompt and look at all the port numbers. Even the console and telnet ports have ... beginners and will offer step-by-step instructions to help you get familiar with Cisco routers and networking Sample Configs; will give you standard router configurations that you can cu...

Ngày tải lên: 11/12/2013, 14:15

... chỉ vì chuyện bao bì đóng gói. The Hale and Hearty colours are not auspicious in our culture. Theo văn hóa của chúng tôi, những màu sắc công ty Hale and Hearty đang dùng không phải là những ... days. Chúng tôi chỉ có thể cho anh thêm 2 ngày nữa thôi. Eng: I have some good news and some bad news. The good news is that we got the shipment out in time. The bad news is that...

Ngày tải lên: 11/12/2013, 16:16

... control commands; 2. Link policy commands; 3. Host controller and baseband commands; 4. Read information commands; 5. Read status commands; 6. Test commands. The link control commands are used ... layers and the HCI interface. The HCI commands for the Bluetooth module are handled by the HCI firmware that access the baseband and link manager. Not all Bluetooth implementations run the low...

Ngày tải lên: 12/12/2013, 09:16

Ngày tải lên: 13/12/2013, 05:15

Ngày tải lên: 13/12/2013, 05:15