N885 Cummins Engine Shop Manual P1

Ngày tải lên: 09/11/2013, 03:15

Ngày tải lên: 09/11/2013, 03:15

... the cold, thickened oil. g. Run the engine at reduced speed only long enough to circulate the oil through the engine. Then increase engine speed and warm up the engine. Low idling speeds during ... temperature. 6. Engine Operation . a. Before starting, make sure fuel and oil in the engine, transmission, and tandems are thin enough to flow. b. If oil drips from the dipstick, it is thi...

Ngày tải lên: 22/10/2012, 09:13

... must be car-ried out under unladen condition* with tires on ground.*: Fuel, radiator coolant and engine oil full. Spare tire, jack,hand tools and mats in designated positions.¼ Use flare nut wrench ... onslopes.1. If the rear wheels slip during thehub locking operation, noise canoccur in the hubs1. Reduce engine speed and drive for-ward slowly. The hubs will lock evenlyand the noise will...

Ngày tải lên: 22/10/2012, 11:50

... ofremoval.11. Refill engine coolant. Refer to MA-18 (“Changing EngineCoolant”, ENGINE MAINTENANCE”).¼ After installation, run engine for a few minutes, and checkfor leaks .ENGINE COOLING SYSTEMKA24DEThermostat ... air cleaner and air duct assembly.7. Refill engine coolant. Refer to MA-18 (“Changing EngineCoolant”, ENGINE MAINTENANCE”).¼ After installation, run engine for a few minu...

Ngày tải lên: 22/10/2012, 11:51

... Separate drive shaft from front final drive. Refer to “DriveShaft”, AX-15.3) Remove engine mounting bolts and raise up engine. 4) Remove front final drive together with differential mountingmember.CAUTION:Be

Ngày tải lên: 22/10/2012, 11:51

... (with KA24DE engine) or the 100A fusible link (with VG33E engine) .Ground is supplied to generator terminal E through body ground E203 (with KA24DE engine) or body groundA1 (with VG33E engine) .With ... located in the fuse and fusible link box (with KA24DE engine) ] or¼ 100A fusible link [letter a, located in the fuse and fusible link box (with VG33E engine) ] and¼ 7.5A fuse (No. 36, lo...

Ngày tải lên: 22/10/2012, 11:51

... emery paper.¼ Check flywheel runout.Maximum allowable runout:Refer to EM-52 (KA24DE engine) or EM-110 (VG33Eengine), “Inspection”, “CYLINDER BLOCK”.ACL079InstallationNGCL0020¼ Apply recommended ... and withdrawal lever and then install dustcover clip.Recommended sealant: Nissan genuine part (KP115-00100), Three Bond TB1212, Loctite Part Number51813, or equivalentGIMAEMLCECFEMTATTFPDAXSUBRSTR...

Ngày tải lên: 22/10/2012, 11:51

... BeltsNGST0009RefertoMA-17(KA24DEengine)orMA-26(VG33Eengine),“Check-ing Drive Belts”, ENGINE MAINTENANCE”.AST253Checking Fluid LevelNGST0010Check fluid level with engine off.Check fluid level referring ... ST-8.2. Run engine at idle speed or 1,000 rpm.¼ Make sure fluid temperature in reservoir tank rises to 60to 80°C (140 to 176°F).WARNING:Warm up engine with shut-off valve fully opened...

Ngày tải lên: 22/10/2012, 11:51

... nameDescriptionST0501S000( — )Engine stand assembly1 ST05011000( — )Engine stand2 ST05012000( — )BaseNT042Disassembling and assemblingKV10106500( — )Engine stand shaftNT028KV10105001( — )Engine attachmentNT031KV101092S0(J26336-B)Valve ... contacting surfaces with new engine oil.¼ Apply new engine oil to bolt threads and seat surfaceswhen installing camshaft sprockets and crankshaft pu...

Ngày tải lên: 22/10/2012, 11:51