Lab: Using Platform Builder

... when you installed Platform Builder. You installed Platform Builder in the default directory provided by the Setup program. Lab: Using Platform Builder 3 Exercise 1 Using Platform Builder with the ... the Platform Builder online Glossary: • Platform • Project • Board Support Package (BSP) • Configuration • Feature • CEPC Estimated time to complete this lab: 35 min...

Ngày tải lên: 04/11/2013, 12:15

... with Platform Builder Components of the IDE  Platform Builder Workspace: Platform vs. Project  FeatureView  ParameterView  Catalog  Output Window  Text editor  Platform Settings Platform Builder ... settings. Build the Platform Image After you have configured your platform, you can build a platform using the Platform Builder integrated development environment...

Ngày tải lên: 22/10/2013, 15:15

... Introduction to Oracle: SQL and PL/SQL Using Procedure Builder Volume Two S Participant Guide Edition 1.1 M03990 T1001E11

Ngày tải lên: 17/01/2014, 09:20

... Introduction to Oracle: SQL and PL/SQL Using Procedure Builder Volume Three S Participant Guide Edition 1.1 M03991 T1001E11

Ngày tải lên: 24/01/2014, 10:20

... Introduction to Oracle: SQL and PL/SQL Using Procedure Builder Volume Four S Participant Guide Edition 1.1 M03992 T1001E11

Ngày tải lên: 24/01/2014, 10:20

... Routing Basics v 3.0 - Lab 9.2.6 Copyright  2003, Cisco Systems, Inc. Lab 9.2.6 Troubleshooting Using Ping and Telnet Objective • Use knowledge of OSI Layers 1, 2 and 3 to diagnose network configuration ... according to the chart. This will introduce some errors. Team member 2 should test the configuration using physical inspection, ping and Telnet. Note: Go to the erase and reload instr...

Ngày tải lên: 19/10/2013, 02:15

... Routing Basics v 3.0 - Lab 9.3.4 Copyright  2003, Cisco Systems, Inc. Lab 9.3.4 Troubleshooting using Traceroute 2 - 3 CCNA 2: Routers and Routing Basics v 3.0 - Lab 9.3.4 Copyright  2003, Cisco ... the configurations on the host and directly connected router. Step 4 Test Layer 3 connectivity Using the command prompt enter ping and the IP address of all routers interfaces. This will tes...

Ngày tải lên: 23/10/2013, 00:15

... configuration file in NVRAM using show startup-config. • View the IOS file information using show flash and show version. • View the current status of the router interfaces using show interface. • ... Systems, Inc. Lab 3.1.4 Using Router show Commands Objective • Become familiar with the basic router show commands. • Retrieve the current running configuration from RAM using show run...

Ngày tải lên: 27/10/2013, 07:15

... Basics v 3.0 - Lab 4.1.4 Copyright  2003, Cisco Systems, Inc. Lab 4.1.4 Creating a Network Map using CDP Objective • Use Cisco Discovery Protocol (CDP) commands to get information about neighboring ... prompt. b. Fill in the following table: Device and Port ID Local Interface Hold Time Capability Platform Upon completion of the previous steps, logoff by typing exit. T...

Ngày tải lên: 04/11/2013, 16:15

... version is used, CDP must be enabled on each of the device interfaces. Enable CDP by using the cdp enable command. Using the command show cdp interface gathers the information that CDP uses for its ... Routers and Routing Basics v 3.0 - Lab 4.1.6 Copyright  2003, Cisco Systems, Inc. Lab 4.1.6 Using CDP Commands Objective • Use CDP commands to obtain information about neighbori...

Ngày tải lên: 05/11/2013, 12:15