Interior Route Redistribution Lab

... 12-01-1999 Interior Route Redistribution by Ronald Trunk Lab Scenario Discussion Incomplete Router Configurations Helpful Hints Solution Lab Scenario Please refer to Figure 1. The challenges of this lab ... between the routers from the remaining address space, using a 24-bit mask. 3. Mutually redistribute routes between the domains. OSPF routes should be given a metric of 6 in the...

Ngày tải lên: 27/10/2013, 07:15

... route command. From the Gadsden router, type the following: 3 - 6 CCNA 2: Routers and Routing Basics v 3.0 - Lab 9.3.5 Copyright  2003, Cisco Systems, Inc. GAD#show ip route b. Is there a route ... routes are now in the routing table. So again issue the show ip route command to verify that the router now has the proper route. b. From the Gadsden router, type the following: GAD#sho...

Ngày tải lên: 23/10/2013, 00:15

... route command. From the Gadsden router, type the following: GAD#show ip route 2 - 6 CCNA 2: Routers and Routing Basics v 3.0 - Lab 9.3.5 Copyright  2003, Cisco Systems, Inc. b. Is there a route ... routes are now in the routing table. So again issue the show ip route command to verify that the router now has the proper route. b. From the Gadsden router, type the following: GAD#sho...

Ngày tải lên: 27/10/2013, 07:15

... 1 - 2 Semester 5: Advanced Routing v2.0 - Lab 7.6.1 Copyright  2001, Cisco Systems, Inc. 7.6.1 Route Optimization Challenge Lab 192.168.200.99/24 192.168.216.88/24 Fa0/0 192.168.200.1/24 Fa0/0 192.168.216.1/24 London ... end of the month. The only monies available for the project are for provisioning WAN links. Design Considerations You are to work with the existing routers...

Ngày tải lên: 21/12/2013, 19:15

... lab to correctly identify the interface identifiers to be used based on the equipment in the lab. The configuration output used in this lab is produced from 1721 series routers. Any other router ... instructions at the end of this lab. Perform those steps on all routers in this lab assignment before continuing. 2 - 6 CCNA 2: Routers and Routing Basics v 3.0 - Lab 9.1.1 Copyright...

Ngày tải lên: 18/01/2014, 05:20

... lab to correctly identify the interface identifiers to be used based on the equipment in the lab. The configuration output used in this lab is produced from 1721 series routers. Any other router ... instructions at the end of this lab. Perform those steps on all routers in this lab assignment before continuing. 1 - 6 CCNA 2: Routers and Routing Basics v 3.0 - Lab 9.1.1 Copyrig...

Ngày tải lên: 18/01/2014, 05:20

... lab to correctly identify the interface identifiers to be used based on the equipment in the lab. The configuration output used in this lab is produced from 1721 series routers. Any other router ... reload instructions at the end of this lab. Perform those steps on all routers in this lab assignment before continuing. Step 1 Configure the routers a. On the routers, enter the glob...

Ngày tải lên: 24/01/2014, 19:20

... a corpus of 427 route in- structions was collected from human sub- jects in the office navigation domain. The instructions were segmented by the steps in the actual route and labeled with the action ... and Buchholz, 2000). Given a sequence of input tokens that forms a route in- struction, a sequence of output labels, with each label matching an input token was prepared. We annotated wit...

Ngày tải lên: 17/03/2014, 04:20

... 1 PE2(config-router)#network 0.0.0.0 0.0.0.0 area 0 PE2(config)#router bgp 1 PE2(config-router)#no synchronization PE2(config-router)#network 192.168.1.4 mask 255.255.255.255 PE2(config-router)#neighbor ... 0 P2(config-router)#network 192.168.1.12 0.0.0.3 area 0 P2(config-router)#network 192.168.1.16 0.0.0.3 area 0 P2(config-router)#network 0.0.0.0 255.255.255.255 area 0 PE2(config)#router os...

Ngày tải lên: 13/08/2012, 16:01

Ngày tải lên: 15/08/2012, 10:15