Máy đào HuynDai R250 - P5 5

... 5-8 GROUP 5 TRAVEL SPEED CONTROL SYSTEMTravel motorRegulatorRegulatorMain control valveArm 1Boom

Ngày tải lên: 27/10/2012, 10:56

... Plug3 Plug4 O-ring5 Spool6 Shim7 Spring8 Spring seat9 Stopper10 Spring11 Plug12 Rod seal13 O-ring14 Push rod15 Plate16 Bushing17 Joint assembly18 Swash plate19 Adjusting nut20 Lock nut21 O-ring22 ... Insert25 Boot26 Handle27 Switch assembly28 Screw29 Switch assembly30 Switch cover40 Boot 2-7 1CROSS SECTION14072SF80 2-7 22. FUNCTIONSFUNDAMENTAL FUNCTIONSThe pilot valve is a valve that co...

Ngày tải lên: 27/10/2012, 10:55

... 3-2 3The oil from the front and rear pump flows through the neutral oil passage, bypass oil passage ... MOTORARM1BOOM2SWINGTRAVEL(LH)TRAVEL(RH)OPTIONBOOM1BUCKETARM2dr2~dr8BUCKET CYLINDERBOOM CYLINDERXBkXBp1STRAIGHTTRAVEL SPOOLGROUP 5 COMBINED OPERATION25073HC21 3-2 4When the swing and boom functions are operated, simultaneously the swing spool and boom spoolschanged. ... MOTORARM1BOOM2SW...

Ngày tải lên: 27/10/2012, 10:55

... LoadCurrent(mA)Current(mA)Pressure(kgf/cm2)Pressure(kgf/cm2)230±30280±30600±30700±30700±30245260600±30700±30700±302250±502150±501200±1001050±1001050±1002000190 0-- -2 15020501200±1001050±1001050±1001900180 0-- -4 7313535563135351008 5-- -HSAUTO DECELOne touch decelKEY STARTHigh powerStandard powerEngine ... more time.5)12345678910Segment( )High idle-900High idle-800High idle-700High i...

Ngày tải lên: 27/10/2012, 10:56

... 5-6 GROUP 3 AUTOMATIC DECELERATION SYSTEMP MFuel injectionpumpAccelactuatorMotor drive signalPotentiometer ... theresult of reducing the engine speed, fuel consumption and noise are effectively cut down during non-operation of the control levers.When the Auto decel lamp is turned off by pressing the switch or

Ngày tải lên: 27/10/2012, 10:56

... relief valve set pressureTime of operationH or S330kgf/cm2-H360 kgf/cm2Even when pressed continuously,it is canceled after 8 sec.・・※Default - Power boost solenoid valve : OFF21075MS06 ... 5-7 GROUP 4 POWER BOOST SYSTEMMain control valveArm 1Boom 2SwingLH travelArm 2BucketBoom 1OptionRH

Ngày tải lên: 27/10/2012, 10:56

... upfunction is canceled- Coolant temperature : Above 30°C- Mode : Default(S mode )- Warming up time : 10 minutes(Max )- Warming up lamp : ON- Default mode- Default mode- Changed mode- Warming up lamp ... lamp- Coolant temperature : Less than 30°C(After engine run )- Accel dial position is under 3- Coolant temperature : Above 30°C- Warming up time : Above 10 minutes- Changed mode se...

Ngày tải lên: 27/10/2012, 10:56

... is canceled- Coolant temperature : Less than 100°C- Engine rpm drop to accel dial 7 position- Overheat warning lamp & buzzer : ON- Return to the mode and accel dial set before- Hold on the ... FUNCTIONActuatedCanceledOverheat warning lamp- Coolant temperature : Above 110°C- Accel dial set : Above 8- Coolant temperature : Less than 100°C- Changed mode set by operator※ If any of the ......

Ngày tải lên: 27/10/2012, 10:56

... 5-1 1GROUP 8 ANTI-RESTART SYSTEMEngineCPU controllerStarterStart safety relayDrive signalCN-92aCN-92b1. ANTI-RESTART FUNCTIONAfter 10 seconds from the ... starter from inadvertent restarting.2. When a replacement or taking-off of the CPU controller is needed, connect CN-92a and CN-92b toensure the engine start without the CPU controller.21075MS10

Ngày tải lên: 27/10/2012, 10:56

... 5-1 2GROUP 9 SELF-DIAGNOSTIC SYSTEMOUTLINEWhen any abnormality occurs in the NEW CAPO system caused by electric ... makes buzzer sound itself to warn the communication error whencommunication problem caused by wire-cut or malfunction of the CPU controller occurs.Cluster displays real time error codes received ... 3PressPressPressPressPress Press0 3 0 6 1 02 0StartPressPressPressPressPressPr...

Ngày tải lên: 27/10/2012, 10:56