Máy đào HuynDai R250 - P5 3

... 5-6 GROUP 3 AUTOMATIC DECELERATION SYSTEMP MFuel injectionpumpAccelactuatorMotor drive signalPotentiometer ... theresult of reducing the engine speed, fuel consumption and noise are effectively cut down during non-operation of the control levers.When the Auto decel lamp is turned off by pressing the switch or

Ngày tải lên: 27/10/2012, 10:56

... Roller bearing451 Spring pin464 Plug468 Plug469 Plug471 O-ring472 O-ring485 O-ring487 O-ring488 O-ring491 Oil seal702 Piston706 O-ring707 O-ring712 Brake spring742 Friction plate743 Separate plate744 ... theresult, the pressure in chamber(g) equals(Ps).Ps×A1=Fsp+Ps×A2Ps=Fsp A1-A2 64mng76gP=P2P=Ps③④(210LC-7) 4-2 9(210LC-7) 4-4 9 2-5 5BRAKE SYSTEMControl valve swing brake systemThis is t...

Ngày tải lên: 27/10/2012, 10:55

... LEVER(RH)HYDTANKLINEFILTERSAFETYSOLENOID VALVEMAX FLOW CUT OFFSOLENOID VALVEPm2MPm2Pm1Pm1BUCKET CYLINDERBOOM CYLINDER25073HC08 3-1 2When carrying out the combined operation of swing and boom or arm of the left control valve, ... boost solenoid valveLine filterMax flow cut off solenoid valveSwing speed reducing valve25073CI03 3-6 BUCKET CYLINDERBOOM CYLINDERARM CYLINDERTRAVEL MOTORSWING...

Ngày tải lên: 27/10/2012, 10:55

... CN-87CN-88 CN-89 CN-133 CN-13CN-66 CN-68 CN-70 CN-88CN-133 CN-137 CN-14021CN-75CN-7612CN-47CN-23(LH)CN-24(RH)101099882 71657654321CS-23 CS-27 CS-50CS-52 CS-54 4-2 2Part name Symbol ... terminal 1-5 , 2-6 )∞Ω(For terminal 5-7 , 6-8 )OFF :∞Ω(For terminal 1-5 , 2-6 )0 Ω(For terminal 5-7 , 6-8 )65312M-M+NC654M321P+SIGP -- 2 4V 1A700mA45Ω20W±5%200W24V 8A12CN-66 CN-68 CN-70 CN-87...

Ngày tải lên: 27/10/2012, 10:56

... LoadCurrent(mA)Current(mA)Pressure(kgf/cm2)Pressure(kgf/cm2)230±30280±30600±30700±30700±30245260600±30700±30700±302250±502150±501200±1001050±1001050±1002000190 0-- -2 15020501200±1001050±1001050±1001900180 0-- -4 7313535563135351008 5-- -HSAUTO DECELOne touch decelKEY STARTHigh powerStandard powerEngine ... more time.5)12345678910Segment( )High idle-900High idle-800High idle-700High i...

Ngày tải lên: 27/10/2012, 10:56

... relief valve set pressureTime of operationH or S330kgf/cm2-H360 kgf/cm2Even when pressed continuously,it is canceled after 8 sec.・・※Default - Power boost solenoid valve : OFF21075MS06 ... 5-7 GROUP 4 POWER BOOST SYSTEMMain control valveArm 1Boom 2SwingLH travelArm 2BucketBoom 1OptionRH

Ngày tải lên: 27/10/2012, 10:56

... 5-8 GROUP 5 TRAVEL SPEED CONTROL SYSTEMTravel motorRegulatorRegulatorMain control valveArm 1Boom

Ngày tải lên: 27/10/2012, 10:56

... upfunction is canceled- Coolant temperature : Above 30°C- Mode : Default(S mode )- Warming up time : 10 minutes(Max )- Warming up lamp : ON- Default mode- Default mode- Changed mode- Warming up lamp ... lamp- Coolant temperature : Less than 30°C(After engine run )- Accel dial position is under 3- Coolant temperature : Above 30°C- Warming up time : Above 10 minutes- Changed mode se...

Ngày tải lên: 27/10/2012, 10:56

... is canceled- Coolant temperature : Less than 100°C- Engine rpm drop to accel dial 7 position- Overheat warning lamp & buzzer : ON- Return to the mode and accel dial set before- Hold on the ... FUNCTIONActuatedCanceledOverheat warning lamp- Coolant temperature : Above 110°C- Accel dial set : Above 8- Coolant temperature : Less than 100°C- Changed mode set by operator※ If any of the ......

Ngày tải lên: 27/10/2012, 10:56

... 5-1 1GROUP 8 ANTI-RESTART SYSTEMEngineCPU controllerStarterStart safety relayDrive signalCN-92aCN-92b1. ANTI-RESTART FUNCTIONAfter 10 seconds from the ... starter from inadvertent restarting.2. When a replacement or taking-off of the CPU controller is needed, connect CN-92a and CN-92b toensure the engine start without the CPU controller.21075MS10

Ngày tải lên: 27/10/2012, 10:56