Automotive mechanics (volume i)(part 2, chapter15) intake and exhaust systems

... chapter three tools and their use Ring and open-end spanners are a combination, with a ring at one end and open jaws at the other The ring end can be used for loosening a bolt or nut and for final ... of a hand lever Tools for threading In the workshop, threads are cut by taps and dies A set of tools consists of a stock and dies and also a tap wrench and taps (Figure...

Ngày tải lên: 14/02/2017, 15:05

... Page 57 chapter four measuring and checking it until the anvil and the spindle are both lightly in contact with the cylinder walls Move the micrometer up and down slightly and also from side to ... 9:43 AM Page 59 chapter four measuring and checking figure 4.13 Sleeve and thimble markings on an inch micrometer To understand the scales, read the main scale first and then...

Ngày tải lên: 14/02/2017, 16:00

... and roller-type bearings, and by special antifriction metals in many plain bearings Application of friction to bearings An appreciation of friction and how it applies in actual bearings is helpful ... chapter five friction and bearings Technical terms Friction, static friction, sliding friction, rolling friction, fluid friction, surface-finish, traction, adhesion,...

Ngày tải lên: 14/02/2017, 16:02

... chapter six seals, gaskets and sealants 95 Oil pan gaskets Manifold gaskets Some oil pans and other parts are made as steel pressings These are not as rigid as cast parts and so require gaskets that ... assembly Handling and storing gaskets Gaskets should be handled and stored carefully to prevent damage which could render the gasket useless Some points to be observed...

Ngày tải lên: 14/02/2017, 16:04

... 001-016_May_chap 01 12/9/06 9:38 AM Page 3 Chapter Motor vehicle components Mechanical arrangements Sections of a motor vehicle The engine assembly Vehicle construction The drive train Transmissions ... enable various components which make up the mechanical section of a motor vehicle to be identified ■ The terms components, parts, units and items are all used in relation to...

Ngày tải lên: 14/02/2017, 14:57

... mechanical items Body repairs are usually carried out in a separate body repair workshop Automotive service procedures All automotive service jobs have certain procedures Procedures are ways of doing ... engine, transmission, body and so on An automotive mechanic must be able to refer to workshop manuals and interpret the information that they contain Workshop manuals have a conte...

Ngày tải lên: 14/02/2017, 15:02

... automatic In a workshop, people have to consider the safety of others as well their own They must understand general workshop safety requirements and, in particular, the need for safety when operating ... or be dropped Safety footwear is designed with reinforced toecaps to provide protection against these types of accidents ■ Open or soft footwear should not be worn in the worksho...

Ngày tải lên: 14/02/2017, 16:06

... consumption and risk of diabetes or of interactions between poultry consumption and BMI and the risk of type DM Red meat consumption was associated with a modest increase in the risk of type DM in the ... and type DM may also reflect other unidentified factors It may be possible that consumption of red meat and processed meat may not incre...

Ngày tải lên: 31/10/2012, 16:49

... 71,3% 2, 2% -36,1% 46,6% -28 ,5% 63 725 ,0% 30 ,2% 22 40 43 32 41 116 140 27 5 503 8 62 1.169 1.390 1.711 16.587 16.8 82 17. 325 18.106 19 .28 0 20 .165 21 . 422 22 .453 22 .704 23 .410 24 .071 25 .086 24 .25 2 25 .939 ... 5.809 6. 527 7.436 Ethanol 21 9 709 853 1.504 2. 3 32 3.103 4 .28 0 4.546 4.974 5.641 5 .20 5 TOTAL 22 .491 21 .611 21 .014 21 .460 20 .549 21 .070...

Ngày tải lên: 20/06/2014, 07:20

... conditions of license Coronal 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 ... reserved Usage subject to terms and conditions of license Coronal 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 15 16 17 18 19 20 21 22...

Ngày tải lên: 29/06/2014, 09:21

... 1995, p 21 8 22 5 J.R Scully and R.G Kelly, Methods for Determining Aqueous Corrosion Reaction Rates, Corrosion: Fundamentals, Testing, and Protection, Vol 13A, ASM Handbook, ASM International, 20 03, ... responses occur at ω1, 2 1, 3ω1, as well as at 2, 2 2, and 3 2, and so forth Additionally, a current response can be seen at various intermodulation frequencies such as...

Ngày tải lên: 10/08/2014, 13:20

Ngày tải lên: 13/03/2016, 13:52