fuzzy control systems - design and analysis
... fuzzy control have sparked a flurry of activities in the analysis and design of fuzzy control systems. In this book, we introduce a wide range of analysis and design tools for fuzzy control systems ... chaotic systems, can be and have been represented by T-S fuzzy models. In the PDC design, each control rule is designed from the corresponding rule of a T-S...
Ngày tải lên: 24/08/2014, 17:20
... for Real-Time Systems 7. Performance Analysis Techniques 6. Software Design Approaches 9. Future Visions on Real-Time Systems 1. Fundamentals of Real-Time Systems 3. Real-Time Operating Systems 4. ... for Real-Time Systems 5. Requirements Engineering Methodologies Real-Time Systems Design and Analysis + 8. Additional Considerations for the Practitioner www.it-ebooks.info...
Ngày tải lên: 24/04/2014, 16:03
... REAL-TIME SYSTEMS 13 ž Specification and design of real-time systems and correct representation of temporal behavior. ž Understanding the nuances of the programming language(s) and the real- time ... real-time systems. 1.3 EXAMPLE REAL-TIME SYSTEMS Embedded real-time systems are so pervasive that they are even found in house- hold appliances and toys. A small sampling of re...
Ngày tải lên: 03/06/2014, 01:51
REAL-TIME SYSTEMS DESIGN AND ANALYSIS phần 1 potx
... Analysis of Polled Loops / 364 7.2.3 Analysis of Coroutines / 364 7.2.4 Analysis of Round-Robin Systems / 364 7.2.5 Response-Time Analysis for Fixed-Period Systems / 367 7.2.6 Response-Time Analysis: ... Data Control Signal 1 Control Signal 2 Control Signal n Camera Input Figure 1.2 Typical real-time control system including inputs from sensors and imaging devices and...
Ngày tải lên: 13/08/2014, 08:20
REAL-TIME SYSTEMS DESIGN AND ANALYSIS phần 2 pptx
... applications, including image processing, avionics systems, and medical systems, and the real-time design issues are the same for them as they are for most other systems. 44 2 HARDWARE CONSIDERATIONS FFFFFFFF FFFFFF00 FFFFFE00 FFC00000 DMA Memory-mapped ... predetermined time) and issues a bus time-out signal. Because of its speed, DMA is often the best method for input and outp...
Ngày tải lên: 13/08/2014, 08:20
REAL-TIME SYSTEMS DESIGN AND ANALYSIS phần 3 docx
... be. 3.4.1.2 Task -Control Block Model If the task -control block model is used, then a list of task -control blocks is kept. This list can be either fixed or dynamic. In the fixed case, n task -control blocks ... The Task -Control Block Model The task -control block model is the most popular method for implementing commercial, full-featured, real-time operating systems because the numbe...
Ngày tải lên: 13/08/2014, 08:20
real time systems design and analysis phần 4 ppt
... diagrams. 4.5 STRUCTURED ANALYSIS AND DESIGN Methods for structured analysis and structured design (SASD) have evolved over almost 30 years and are widely used in real-time applications, probably ... consideration as well as pre- and postconditions, and exceptions. In an iterative-development lifecycle these use cases will become increasingly refined and detailed as the an...
Ngày tải lên: 13/08/2014, 08:20
REAL-TIME SYSTEMS DESIGN AND ANALYSIS phần 5 doc
... characteristics: 1. Four-way crossing. 2. Roadway gradients and curvatures are small enough to be neglected. 3. No right-turn or left-turn lanes or right-turn and left-turn signals (note, however, that ... Intersection Control System provides the following functions: 1. Control of the intersection vehicle traffic standards. 2. Control of the intersection pedestrian traffic standards....
Ngày tải lên: 13/08/2014, 08:20
REAL-TIME SYSTEMS DESIGN AND ANALYSIS phần 6 docx
... specifica- tion and design of software-intensive systems using an object-oriented approach. By bringing together the “best-of-breed” in specification techniques, the UML Table 5.3 The set of design ... SPECIFICATION 285 Running Phase RR-RR-RR-RR Phase GG-GG-RR-RR + Do Action / setPhase(void) + Do Action / loadTimer(Phase 1 Time) + Do Action / checkPhase(Phase 1) Phase GY-GY-RR-RR + Do A...
Ngày tải lên: 13/08/2014, 08:20
REAL-TIME SYSTEMS DESIGN AND ANALYSIS phần 7 potx
... object-oriented programming languages. 6.3.2 Call-by-Value and Call-by-Reference The two most widely found parameter passing methods are call-by-value and call-by-reference. 3 In call-by-value ... Details m_ManualOverride :Override «singleton» m_IntersectionController :IntersectionController «resource» :Manual Control Panel Name: IntersectionController- Manual Override Author: Team 2 Ve...
Ngày tải lên: 13/08/2014, 08:20