Mastercam Version 9 SolidsTutorial - Part 6 pdf

... Race Car Mastercam Version 9 Solids Tutorial 153 6. Zoom in on the end of the windshield that contains the light-blue circles. These circles represent the through-holes. Your part should ... six circles. 8. Fit the geometry to the screen. Your part should look like the following picture. 1 2 Chapter 6 1 56 Mastercam Version 9 Solids Tutorial Note: If you do n...

Ngày tải lên: 14/08/2014, 11:20

... Chapter 5 124 Mastercam Version 9 Solids Tutorial Chapter 5 114 Mastercam Version 9 Solids Tutorial Exercise 2 – Creating the die stock In this exercise, you will create a block-shaped solid ... visible levels and display lines 1. Open rod-solid-mm.mc9 from your working folder. Note: If you did not complete Chapter 4, open rod-solid-backup- mm.mc9. 2. Choose the L...

Ngày tải lên: 14/08/2014, 11:20

... Connecticut, 060 8 4-2 830 USA Phone ( 860 ) 87 5-5 0 06 Fax ( 860 ) 87 2-1 565 BBS ( 860 ) 87 1-8 050 TELNET and ftp:// ftp .mastercam. com or 172. 16. 100.100 Internet Address http://www .mastercam. com E-mail ... Mastercam Shortcut Keys 2 69 Version 9 Solids Tutorial (Metric version) Mastercam Version 9 Sol...

Ngày tải lên: 14/08/2014, 10:22

... to your working folder: Mcam9\Tutorials\Solids Tutorial\Metric. 6. Type chair-solid-mm.mc9 for File name and choose Save. Designing a Chair Seat Mastercam Version 9 Solids Tutorial 15 2. Choose ... Chapter 2 6 Mastercam Version 9 Solids Tutorial The following picture shows you some of the main features of the Mastercam workspace. Learning about the HASP and NetHASP...

Ngày tải lên: 14/08/2014, 10:22

... Body. 9. Choose Extend through all. Designing a Plastic Cap Mastercam Version 9 Solids Tutorial 67 9. Choose OK to cut the snap edge. 10. Turn on shading. 11. Choose the Screen-Unzoom ... following picture. Designing a Plastic Cap Mastercam Version 9 Solids Tutorial 61 16. Right-click in the graphics window and choose Side. Your part should look like the following...

Ngày tải lên: 14/08/2014, 10:22

... 9. Choose OK to create the solid. 10. Press [Alt+S] to turn on shading. Your part should look like the following picture. Chapter 4 90 Mastercam Version 9 Solids Tutorial Exercise 6 ... Designing a Connecting Rod Mastercam Version 9 Solids Tutorial 99 14. Turn on shading. Your part should look like the following picture. Notice that the center line of the part...

Ngày tải lên: 14/08/2014, 10:22

... 6. Choose Done. The Extrude Chain dialog box opens. 7. Enter Sprue Hole Core for the operation name. 8. Select Cut Body. 9. Select Extend through all. Chapter 7 1 96 Mastercam Version 9 ... editing purposes later. Chapter 7 200 Mastercam Version 9 Solids Tutorial Designing an Injection Mold for a Camera Mastercam Version 9 Solids Tutorial 191 S p rue hole c...

Ngày tải lên: 14/08/2014, 11:20

... button. 9. Select the top face, as shown in the following picture. Designing an Injection Mold from a Surface File Mastercam Version 9 Solids Tutorial 203 6. Choose the Screen-Statistics ... 8 240 Mastercam Version 9 Solids Tutorial 8. Choose OK. 9. Mastercam prompts you to select a solid for which to create the drawing layout. Select the mold core (light blue sol...

Ngày tải lên: 14/08/2014, 11:20

... Chapter 9 266 Mastercam Version 9 Solids Tutorial 6. Choose OK to cut the electrode. Your part should look like the following picture. 7. Save the file. Chapter 9 262 Mastercam Version 9 ... electrode to view the Y-shaped standoff. 14. Fit the geometry to the screen. Your part should look similar to the following picture. Chapter 9 260 Mastercam Vers...

Ngày tải lên: 14/08/2014, 11:20

... mạch tự động: - Thiết lập những thuộc tính cho đường vẽ (nets). - Kiểm tra boardoutline, định nghóa via và lưới vẽ. - Vẽ đường Vcc và Gnd. - Vẽ trước những đường phức tạp. - Load file chiến ... Hữu Danh Trang 97 - Để ấn định số lớp mạch in c ầnvẽ ta ch ọn ‘ View Spreadsheet ’ ‘ Layer ’ → Chương 4: OrCAD Layout 9. 2 - Nhấp chuột vào ‘View Spreadsheet’, chọn ‘...

Ngày tải lên: 27/07/2014, 16:21