Volume 01 - Properties and Selection Irons, Steels, and High-Performance Alloys Episode 11 pdf

... Nickel and Nickel Alloys Beryllium-Copper and Beryllium-Nickel Alloys Cobalt and Cobalt Alloys Magnesium and Magnesium Alloys Tin and Tin Alloys Zinc and Zinc Alloys Lead and Lead Alloys ... present volume is to document these advances as they pertain to the properties and selection of cast irons, steels, and superalloys. A companion volume...

Ngày tải lên: 10/08/2014, 12:21

... W/(m · K) Shrinkage, % 1 0-2 0 32 0-3 80 4 6-5 5 2-5 5 0-5 2 1. 8-2 .2 2 0-3 0 38 0-4 50 5 5-6 5 2-6 4 8-5 0 2. 0-2 .6 4 0-5 0 45 0-5 00 6 5-7 3 3-6 3 8-4 2 3. 2-4 .6 Thermal Expansion. For irons ... Total carbon 2. 2-2 .9 2. 0-2 .9 Silicon 0. 9-1 .9 0. 9-1 .9 Manganese 0. 2-0 .6 0. 2-1 .3 Sulfur 0.0 2...

Ngày tải lên: 10/08/2014, 12:21

... (a) SAE-AISI number C Mn P max S max M1008 0.10 max 0.2 5-0 .60 0.04 0.05 M 1010 0.0 7-0 .14 0.2 5-0 .60 0.04 0.05 M 1012 0.0 9-0 .16 0.2 5-0 .60 0.04 0.05 M 1015 0.1 2-0 .19 ... 0.2 5-0 .60 0.04 0.05 M 1017 0.1 4-0 .21 0.2 5-0 .60 0.04 0.05 M1020 0.1 7-0 .24 0.2 5-0 .60 0.04 0.05 M1023 0.1 9-0 .27 0.2 5-...

Ngày tải lên: 10/08/2014, 12:21

... Microstructure and Properties, Annual Statistical Report, Scr. Metall., Proceedings of the Fifth International Conference on the Strength of Metals and Alloys, Encyclopedia of Materials Science and Engineering, 1989 ... Engineering, 1989 SAE Handbook, Materials, 1989 SAE Handbook, Materials, 1989 SAE Handbook, Materials, 1989 SAE Handbook, Materials, International Metallic Material...

Ngày tải lên: 10/08/2014, 12:21

... -0 .15 -0 .006 -0 .18 -0 .007 - 0.20 - 0.008 -0 .20 -0 .008 >15 2-2 03 inclusive > 6-8 inclusive - 0.15 - 0.006 -0 .18 -0 .007 -0 .20 -0 .008 - 0.23 - 0.009 -0 .23 -0 .009 >20 3-2 29 ... 1 2 inclusive - 0.05 - 0.002 -0 .08 -0 .003 -0 .10 -0 .004 - 0.13 - 0.005 -0 .13 -0 .005...

Ngày tải lên: 10/08/2014, 12:21

... helical springs made from chromium-silicon steel (a and b), oil- tempered wire (c and d), and hard- drawn spring wire (e and f). The graphs on the left (a, c, and e) plot maximum allowable stress ... of amines, carbonates, acidified cyanides, hydroxides, nitrates, and anhydrous ammonia. Carbon steels, low-alloy steels, and H -1 1 tool steels with ultimate tensile strengt...

Ngày tải lên: 10/08/2014, 12:21

... Low-carbon steel 0.29 0.6 0- 1.35 0.1 5- 0.40 (b) 17 0- 250 2 5- 36 31 0- 415 4 5-6 0 2 3-3 0 As-hot rolled carbon- manganese steel 0.40 1.0 0- 1.65 0.1 5- 0.40 . . . 25 0- 400 3 6- 58 41 5- 690 ... Quenched and tempered 0.20 1.50 max 0.1 5- 0.30 0.0005 B min 55 0- 690 8 0- 100 66 0- 760 9 5- 110 18 Quenched and t...

Ngày tải lên: 10/08/2014, 12:21

... Austenitize: 870 °C (1600 °F) Hardenability Curves for Nickel-Chromium-Molybdenum (81xx) Alloy Steels Figure 63. SAE/AISI 81B45H UNS H81451. Heat-treating temperatures recommended by SAE Normalize ... °C (1550 °F) Hardenability Curves for Nickel-Chromium-Molybdenum (88xx) Alloy Steels Figure 81. SAE/AISI 8822H UNS H88220. Heat-treating temperatures recommended by SAE Norma...

Ngày tải lên: 10/08/2014, 12:21

... Vol 14A, June 1983, P 112 1-1 133 126. H. Kwon and C.H. Kim, Tempered Martensite Embrittlement in Fe-Mo-C and Fe-W-C Steel, Metall. Trans. A, Vol 14A, July 1983, p 138 9-1 394 127. R.M. Horn ... 0.0 6-0 .08 Line C 3.5 1.7 . . . >0.08 Line D 3.5 . . . 0.4 0.0 6-0 .08 Line E . . . 1.7 0.4 0.0 6-0 .08 Plain carbon of 11...

Ngày tải lên: 10/08/2014, 12:21

... 0.3 0-0 .60 . . . H22 T20822 0.3 0-0 .40 0.1 5- 0.40 0.1 5- 0.40 1.7 5-3 .75 0.30 max . . . 10.0 0- 11. 75 0.2 5-0 .50 . . . H23 T20823 0.2 5-0 .35 0.1 5-0 .1 5-1 1.0 0-0 .30 . . . 11. 0 0-0 .7 5-1 .25 ... 1200 (f) 84 5-9 00 155 0- 1650 5-2 0 B or W 17 5- 425 35 0-8 00 S5 Slowly 760 1400 87 0-9 25 160 0- 1700 5-2 0 O...

Ngày tải lên: 10/08/2014, 12:21