Volume 01 - Properties and Selection Irons, Steels, and High-Performance Alloys Episode 7 pps
Volume 01 - Properties and Selection Irons, Steels, and High-Performance Alloys Part 1 docx
... etc. I. ASM International. Handbook Committee. II. Title: ASM Handbook.
TA459.M43 1990 620.1'6 9 0-1 15
ISBN 0-8 71 7 0-3 7 7- 7 (v.1)
SAN 20 4 -7 586
ISBN 0-8 71 7 0-3 8 0 -7
Printed in the United States ...
Nickel and Nickel Alloys
Beryllium-Copper and Beryllium-Nickel Alloys
Cobalt and Cobalt Alloys
Magnesium and Magnesium Alloys
Tin and...
Volume 01 - Properties and Selection Irons, Steels, and High-Performance Alloys Part 2 pptx
...
W/(m · K)
Shrinkage, %
1 0-2 0 32 0-3 80
4 6-5 5
2-5 5 0-5 2
1. 8-2 .2
2 0-3 0 38 0-4 50
5 5-6 5
2-6 4 8-5 0
2. 0-2 .6
4 0-5 0 45 0-5 00
6 5 -7 3
3-6 3 8-4 2 3. 2-4 .6
Thermal Expansion. For irons ... strength and ultrasonic velocity or resonant frequency for test
bars of 30 mm (1.2 in.) diameter.
M5003
(c)
5 17 75 3...
Volume 01 - Properties and Selection Irons, Steels, and High-Performance Alloys Part 3 pot
...
G10390
1039 0.3 7- 0 .44 0 .7 0-1 .00 0.040
0.050
G10400
1040 0.3 7- 0 .44 0.6 0-0 .90 0.040
0.050
G10420
1042 0.4 0-0 . 47 0.6 0-0 .90 0.040
0.050
G10430
1043 0.4 0-0 . 47 0 .7 0-1 .00 0.040
0.050 ...
0.2 5-0 .60
0.04
0.05
M 10 17 0.1 4-0 .21
0.2 5-0 .60
0.04
0.05
M1020 0.1 7- 0 .24
0.2 5-0 .60
0.04
0.05
M1023 0.1 9-0 ....
Volume 01 - Properties and Selection Irons, Steels, and High-Performance Alloys Part 4 ppsx
... Microstructure and Properties,
Annual Statistical Report,
Scr. Metall.,
Proceedings of the Fifth International
Conference on the Strength of Metals and Alloys,
Encyclopedia of Materials Science and Engineering,
1989 ... Engineering,
1989 SAE Handbook, Materials,
1989 SAE Handbook, Materials,
1989 SAE Handbook, Materials,
1989 SAE Handbook, Materials,
International Metallic Material...
Volume 01 - Properties and Selection Irons, Steels, and High-Performance Alloys Part 5 potx
...
-0 .15
-0 .006 -0 .18 -0 .0 07 -
0.20
-
0.008
-0 .20
-0 .008
>15 2-2 03
inclusive
> 6-8 inclusive -
0.15
-
0.006
-0 .18
-0 .0 07 -0 .20 -0 .008 -
0.23
-
0.009
-0 .23
-0 .009
>20 3-2 29 ...
1
2
inclusive
-
0.05
-
0.002
-0 .08
-0 .003 -0 .10 -0 .004 -
0.13
-
0.005
-0 .13
-0...
Volume 01 - Properties and Selection Irons, Steels, and High-Performance Alloys Part 6 pot
... 0.81 0.032 9.52 0. 375
10 .7
2 0.81 0.032 6.35 0.250
6.8
3 1.22 0.048 15.88 0.625
12.0
4 2.59 0.102 22.22 0. 875
7. 6
5 3. 07 0.121 22.22 0. 875
6.2
6 450 0. 177 22.22 0. 875 4.9
Free length ...
resistance at elevated temperature
High-
temperature
alloys
Inconel X -7 5 0,
AMS 5542
Ni 73 , Cr 15, Fe
6 .75
1030 (150) 215 (31) . . . . . . 30 min 40 0-5 90
(75 0-1 100...
Volume 01 - Properties and Selection Irons, Steels, and High-Performance Alloys Part 7 potx
...
10 5-
130
585 85 17 35 0.20 0.5 0-
0.80
0.60 0.5 0-
0.80
0 .7 0-
1.10
0.4 5-
0.65
(p)
,
(s)
12A (NT)
48 5-
655
7 0-
95
275 40 20 35 0.20 0.4 0-
0 .70
0.60 0.5 0-
0.90
0.6 0-
1.00
0.9 0-
1.20 ...
Low-carbon steel 0.29 0.6 0-
1.35
0.1 5-
0.40
(b)
17 0-
250
2 5-
36
31 0-
415
4 5-6 0
2 3-3 0
As-hot rolled carbon-
m...
Volume 01 - Properties and Selection Irons, Steels, and High-Performance Alloys Part 9 pptx
... Nickel-Chromium-Molybdenum (87xx) Alloy Steels
Figure 79 . SAE/AISI 872 0H UNS H 872 00. Heat-treating temperatures recommended by
SAE Normalize (for forged or rolled specimens only): 925 °C ( 170 0 ... ( 170 0 °F) Austenitize: 925 °C ( 170 0
°F)
Hardenability Curves for Nickel-Chromium-Molybdenum (47xx) Alloy Steels
Figure 40. SAE/AISI 471 8H UNS H 471 80. Heat-treating temperature...
Volume 01 - Properties and Selection Irons, Steels, and High-Performance Alloys Part 11 pptx
... Trans. ASM, Vol 62, 1969, p 1016 - 1018
100.
D.F. Stein, Reversible Temper Embrittlement, Annu. Rev. Mater. Sci. 1 977 , Vol 7, 1 977 , p 12 3-1 53
101.
L.D. Jaffe and D.C. Buffum, Isothermal Temper ... Dec 1969, p 161 9-1 623
61.
H.J. Kerr and F. Eberle, Graphitization of Low-Carbon and Low-Carbon-Molybdenum Steels,
Trans.
25,000 h at 25 °C (75 °F) and 230 °C...
Volume 01 - Properties and Selection Irons, Steels, and High-Performance Alloys Part 12 potx
...
O1 870 1600 76 0 -7 90 140 0-1 450 22 40
18 3-2 12
O2 845 1550 84 5 -7 70 1 37 5-1 425 22 40
18 3-2 12
O6 870 1600 76 5 -7 90 141 0-1 450 11 20
18 3-2 17
O7 900 1650 79 0-8 15 145 0-1 500 22 40
19 2-2 17
Shock-resisting ... 1200
(f)
84 5-9 00 155 0-
1650
5-2 0 B or W 17 5-
425
35 0-8 00
S5 Slowly 76 0 1400 87 0-9 25 160 0-
170 0...
Từ khóa: