product design development 10 pps
product design development 10 pps
... 551 Design for Manufacturing 1 Product Design & Development Design for Manufacturing ETM 551 Design for Manufacturing 5 Planning Planning DFM within Product Development Process Concept Development Concept Development System-Level Design System-Level Design Detail Design Detail Design Testing ... Process Concept Development Concept Development System-Lev...
Ngày tải lên: 13/08/2014, 05:21
product design development 2 pps
... process Planning Planning Concept Development Concept Development System-Level Design System-Level Design Detail Design Detail Design Testing and Refinement Testing and Refinement Production Ramp-Up Production Ramp-Up Four Phases of Product Development 9 The ... Derivatives time Platform B Platform Product Development Derivative Product Development Legend Project Prod...
Ngày tải lên: 13/08/2014, 05:21
Geometric Dimensioning and Tolerancing for Mechanical Design Part 10 ppsx
... a tolerance of .005 at RFS to datum A at RFS. 2.000-2.0044.000 A Figure 10- 10 Symmetry of the slot: Problem 4. 4. The part in Fig. 10- 10 rotates at a high speed, and the mass must be accu- rately balanced. ... PBU MHBD031 -10 MHBD031-Cogorno-v5.cls April 11, 2006 23:3 176 Chapter Ten 3 X 24.990-25.000 Figure 10- 9 Coaxiality of the hexagon: Problem 3. 3. The mass of the hexagon shown in...
Ngày tải lên: 05/08/2014, 09:20
Handbook of Materials for Product Design Part 8 ppsx
... –40 –30 T +10 — –5 to +10 –30 –50 NBR +10 0 to +5 10 to +5 –20 –30 FVMQ +10 0 to +10 0 to 10 –35 –30 FKM +10 06aOhm Page 17 Wednesday, May 23, 2001 10: 12 AM 6.18 Chapter 6, Part 1 6.7.1 ... +80 10 to +15 –45 –30 CSM +80 EAM +80 +50 –50 –50 MQ +80 +60 –30 max. AU, EU +40 0 to +6 10 to +5 –35 –40 ECO +30 0 to +15 –5 to +10 10 –50 ACM ±30 +25 –20 max. –40 –30 T +10 — –5 to +1...
Ngày tải lên: 10/08/2014, 19:20
Handbook of Materials for Product Design Part 10 docx
... thermal expansion between 35 and 125 × 10 –7 /°C. For devitrifying sealing glasses, softening points range from 310 to 645°C; expansion from 42 to 100 × 10 –7 /°C. Thermal expansion of sealing ... commercial sealing glasses are given in Tables 8.9 and 8 .10. Typically, sealing glasses are supplied as 100 -mesh powder (pass through screen of 100 mesh/inch), called frit, which is mix...
Ngày tải lên: 10/08/2014, 19:20
Handbook of Materials for Product Design Part 11 pps
... Tempering Practices Tempering is usually accomplished by heating the glass product, gen- erally to a viscosity of about 10 9.5 to 10 10 P for a short while, and then quenching symmetrically from both ... w–()== 08Seward Page 110 Wednesday, May 23, 2001 10: 16 AM Inorganic Glasses 8.133 glass products are ion exchange strengthened: windshields for aircraft, borosilicate glass syringes...
Ngày tải lên: 10/08/2014, 19:20
Handbook of Materials for Product Design Part 16 pps
... be prohibitive to production if the product volume is relatively low. An off- the-shelf product that already carries the approvals may be the only vi- able alternative. There may also be product test ... government regulations concerning product safety and only indicate a valid design. These tests usually provide no insight into production anomalies, offer no protection from product...
Ngày tải lên: 10/08/2014, 19:20
Handbook of Materials for Product Design Part 18 ppsx
... plating 10. 38 electroplating 10. 36 engineering types 10. 35 flame spray 10. 36 fume suppressants 10. 37 functional 10. 40 hard 10. 35 10. 40 hydrogen embrittlement 10. 41 industrial 10. 35 10. 40 ... black chromium 10. 43 chromic oxide 10. 35 chromising 10. 36 chromium nitride 10. 42 chromous chloride 10. 42 coatings 10. 35 crack-controlled 10. 37 decorativ...
Ngày tải lên: 10/08/2014, 19:20
Plastics Engineered Product Design Part 2 ppsx
... parameters going from the product design through production. Examples of potential cost reductions include. (1) redesign product with thinner walls to reduce production cost, etc. (2) ... start of production, analyze complete design (again1 to change design/ production/safety factors in order to reduce costs t 48 Plastics Engineered Product Design plane considere...
Ngày tải lên: 12/08/2014, 01:21
Plastics Engineered Product Design Part 9 pps
... coefficients on the composite optimum design? as design variables for the multilayered-filamentary composite? composite optimum design? 31 8 Plastics Engineered Product Design conductive coatings ... difficulty if the design requires penetrations and hatches in the glass hull. A solution could be filament winding RP around the glass or using a 3 10 Plastics Engine...
Ngày tải lên: 12/08/2014, 01:22