Engineering Tribology 2011 Part 11 docx

... Performance, Tribology, Vol. 6, 1973, pp. 219-251. 54 W. Liu, C. Huang, L. Gao, J. Wang and H. Dang, Study of the Friction and Wear Properties of MoS 2 -filled Nylon 6, Wear, Vol. 151, 1991, pp. 111 -118 . 55 ... or bonding between powder particles in the coating must be strong. These conditions often remain unfulfilled when the coating material is deposited as partially molten particles or...

Ngày tải lên: 12/08/2014, 03:20

... Bioengineering, San Diego, Vol. II, 1990, pp. 269. 21 Z. Rymuza, Tribology of Miniature Systems, Elsevier, Tribology Series 13, 1989. 40 ENGINEERING TRIBOLOGY Oil sample 300 ml Water 60 ml Condenser jacket Condenser water in Condenser water out Dried ... the winter grade is defined by the temperature at which the oil reaches the 50 ENGINEERING TRIBOLOGY 46 ENGINEERING TRIBOLOG...

Ngày tải lên: 12/08/2014, 03:20

... partner. External SCC drivers : External complexity driver is related with material and information flows exported by other business partners (customer and supplier) to a single business partner ... cooperation, collaboration and integration among supply chain participants etc. A supply chain consists of multiple business partners who work together directly or indirectly which is collabo...

Ngày tải lên: 20/06/2014, 04:20

... Waste Water - Treatment and Reutilization 266 The rate constants k 1 , k 1 `, k 2 , k 2 `, k 11 , k 11 `, k 21 and k 21 ` were obtained by the least-square fitting method. Results obtained were ... 0.87 157 Sulfamethizole 22.3 0.22 - 0.64 214 Sulfadimethoxine 18.8 0.38 - - - Sulfasoxazole 11. 0 2.42 - 0.85 161 Half lives for the dose of 1 mg/L of K 2 FeO 4 at pH 7.0 and 25 0 C...

Ngày tải lên: 21/06/2014, 23:20

Ngày tải lên: 10/08/2014, 20:20

... (steady part) and fluctuations (unsteady part) as follows: u = u + u  ,  =  +   , p = p + p  (9.2) where ( ) shows the time average or the steady part, and (  ) indicates the unsteady part. ... Vol. 181, Part 3O, 1966-1967, pp. 117 - 126. 6. R.G. Woolacott, W.L. Cooke, “Thermal Aspects of Hydrodynamic Journal Bearing Per- formance at High Speeds”, Proc. I. Mech. E., Vol. 181, Pa...

Ngày tải lên: 11/08/2014, 08:21

Ngày tải lên: 11/08/2014, 15:21

... calibration depends on number of linear parts. The number of linear parts depends only on character of conversion characteristic therefore individual parts would have not same length. It leads ... ( ) ( ) ( ) ( ) ( ) ()()( )( )( ) niiiiiii nii i xxxxxxxxxx xxxxxxxxxx −−−−− −−−−− = +− +− 112 1 112 1 λ (8) The calibration data are stored in on chip memory. Robotics, Automation and C...

Ngày tải lên: 11/08/2014, 21:22

... 2.00 2.10 2.20 2.30 2.40 2.50 2.60 2.70 2.80 2.90 3.00 3.10 3.20 3.30 3.40 3.50 3.60 3.70 3.80 3.90 4.00 4.10 4.20 4.30 4.40 4.50 4.60 4.70 4.80 4.90 5.00 5.10 5.20 5.30 5.40 5.50 5.60 5.70 5.80 5.90 6.00 6.10 6.20 6.30 6.40 6.50 6.60 6.70 6.80 6.90 7.00 7.10 7.20 7.30 7.40 7.50 7.60 7.70 7.80 7.90 8.00 8.10 8.20 7.994 8.640 9.309 10.00 10.71 11. 45 12.21 13.00 13.80 14.63 15.49 16.36 17.26...

Ngày tải lên: 12/08/2014, 03:20

... Additives in Greases, Tribology International, Vol. 7, 1974, pp. 113 -118 . 20 R. O’Halloran, J.J. Kolfenbach and H.L. Leland, Grease Flow in Shielded Bearings, Lubrication Engineering, Vol. 14, ... Phase Systems, Proc. Int. Tribology Conference, Melbourne, The Institution of Engineers, Australia, National Conference Publication No. 87/18, December, 1987, pp. 110 -115 . 16 K.E. Bett a...

Ngày tải lên: 12/08/2014, 03:20