Modelling with AutoCAD 2011 Part 2 docx

... fig(h) 5 Menu bar with Tools-New UCS-Z and: prompt Specify rotation angle about the Z axis enter –90 <R> – fig(i) 34 Modelling with AutoCAD 20 02 modelling with AutoCAD. qxd 17/06 /20 02 15:37 Page ... not as 3DWFM 48 Modelling with AutoCAD 20 02 modelling with AutoCAD. qxd 17/06 /20 02 15:37 Page 48 Setting a new UCS position The user can set a new UCS posit...

Ngày tải lên: 12/08/2014, 02:23

... are now ready to proceed with creating 3D and solid models. 4 Modelling with AutoCAD 20 02 modelling with AutoCAD. qxd 17/06 /20 02 15:37 Page 4 Modelling with AutoCAD 20 02 Bob McFarlane MSc, BSc, ... 29 5 Chapter 45 Rendering 3 02 Chapter 46 Publishing to the web 3 12 Chapter 47 Students’ models 316 Activities 323 Index 335 vi Modelling with AutoCAD 20 02...

Ngày tải lên: 12/08/2014, 02:23

... viewport 62 Modelling with AutoCAD 20 02 modelling with AutoCAD. qxd 17/06 /20 02 15:38 Page 62 20 The screen display should resemble Fig. 9 .2( c) 21 Save the screen configuration as CONF4 22 Task Restore ... Modelling with AutoCAD 20 02 Figure 10.1 3D Views – the VPOINT ROTATE option with 3DWFM. modelling with AutoCAD. qxd 17/06 /20 02 15:38 Page 66 The Vie...

Ngày tải lên: 12/08/2014, 02:23

... to (a), create the model with the MODEL tab active 120 Modelling with AutoCAD 20 02 modelling with AutoCAD. qxd 17/06 /20 02 15:39 Page 120 6 Set both SURFTAB1 and SURFTAB2 to 18 7 Using the Edge ... the model to ‘see inside’ the raised part of the edge surface. 1 32 Modelling with AutoCAD 20 02 modelling with AutoCAD. qxd 17/06 /20 02 15:39 Page 1 32 3D o...

Ngày tải lên: 12/08/2014, 02:23

... fig(a). Figure 22 .7 The EXTEND and TRIM commands. 148 Modelling with AutoCAD 20 02 modelling with AutoCAD. qxd 17/06 /20 02 15:40 Page 148 4 Zoom centre about 320 , 320 ,100 at 700 in all viewports 5 With the ... model as MODR20 02\ WALL 158 Modelling with AutoCAD 20 02 Figure 23 .7 The completed wall clock created from inserted wblocks. modelling with AutoCAD....

Ngày tải lên: 12/08/2014, 02:23

... restore the original polyline outline 20 2 Modelling with AutoCAD 20 02 Figure 29 .6 Revolved example 2 – a shaft. modelling with AutoCAD. qxd 17/06 /20 02 15:41 Page 20 2 Using 3D orbit 1 The ARCHES model ... space with the lower left viewport active, restore UCS BASE with layer MODEL current 1 82 Modelling with AutoCAD 20 02 modelling with AutoCAD. qxd 1...

Ngày tải lên: 12/08/2014, 02:23

... the ‘interpenetration’ effect 22 4 Modelling with AutoCAD 20 02 Figure 34 .2 Chamfered and filleted composite. modelling with AutoCAD. qxd 17/06 /20 02 15:41 Page 22 4 Summary 1 Swept solids are obtained with the extrude ... other commands. 22 0 Modelling with AutoCAD 20 02 Figure 33.1 The completed composite model 3 – pipe/flange. modelling with AutoCAD. qxd 17...

Ngày tải lên: 12/08/2014, 02:23

... the layout when complete. 25 8 Modelling with AutoCAD 20 02 Figure 39 .2 The PROFILE command with the flange/pipe model. modelling with AutoCAD. qxd 17/06 /20 02 15: 42 Page 25 8 Summary 1 Mass properties ... purposes 2 Each scaled part is positioned on top of the previous part 3 Use your discretion for sizes not given 24 0 Modelling with AutoCAD 20 02 model...

Ngày tải lên: 12/08/2014, 02:23

... etc. 27 2 Modelling with AutoCAD 20 02 Figure 41.3 Extracting details for the desk tidy model. modelling with AutoCAD. qxd 17/06 /20 02 15: 42 Page 27 2 3 Create three cylinders, colour magenta with: cylinder ... about the point 0,0 for four items with rotation, the angle to fill being –180 28 2 Modelling with AutoCAD 20 02 modelling with AutoCAD. qxd 17/06 /...

Ngày tải lên: 12/08/2014, 02:23

... 309 modelling with AutoCAD. qxd 17/06 /20 02 15:43 Page 309 322 Modelling with AutoCAD 20 02 Figure 47.11 Figure 47. 12 Gary Jamieson. modelling with AutoCAD. qxd 17/06 /20 02 15:43 Page 322 314 Modelling ... 2 Activate the model tab 310 Modelling with AutoCAD 20 02 Figure 45.4 The rendered WALL CLOCK with materials attached. modelling with AutoCAD. q...

Ngày tải lên: 12/08/2014, 02:23