Process Engineering Equipment Handbook 2009 Part 16 pdf

... specifications. These processes are discussed in more detail in the following subsections. A simplified flow diagram of the various refinery processes and products is provided in Fig. R-1. Refinery Processes Separation Atmospheric ... processes. Typical cracking processes include catalytic cracking, hydrocracking, and visbreaking or coking, both of which are thermal cracking processes. 1. Catalyt...

Ngày tải lên: 12/08/2014, 02:20

... Filsorption II process) is used for separation of submicron particles, heavy metals, and toxic hydrocarbons by a combination of filtering, “sorption,” and chemical reaction. The Wetpac ® process is ... and controlling air pollution include: ᭿ Electrostatic precipitators (for particulates) ᭿ Fabric filters (for dust and particulates) ᭿ Flue gas desulfurization (for SO x removal) ᭿ SCR DeNO x...

Ngày tải lên: 12/08/2014, 02:20

... inspection is performed during the manufacturing process after each important step. All pressure-stressed parts, such as cylinders, cylinder covers, C- 116 Compressors FIG. C-102D With gas- and pressure-tight ... cryogenic temperatures. LNG at barometric pressure boils off at -160 °C. This temperature is well below the limit where some of the common engineering Compressors C-121 FIG. C-1...

Ngày tải lên: 12/08/2014, 02:20

... Buscarello, R., vibration course notes, 1980. 19. Handbook on vibration, McGraw-Hill, New York. 20. Bloch, H., and Soares, C. M., Turboexpanders and Process Application, Gulf Professional Pub., 2001. Control ... what controls and governs an operating system or part of that system. The field of controls and control systems is wide enough to fill several handbooks on its own. However, in th...

Ngày tải lên: 12/08/2014, 02:20

... efficiency: 100 percent for particles of 8 microns and larger, 99 percent for particles of 6 to 8 microns, 90 percent for particles of 4 to 6 microns, and 85 percent for particles of 2 to 4 microns. ... for particles 3 microns and larger, and 99.98 percent for particles less than 3 microns. Solids removal efficiency: 100 percent for particles of 3 microns and larger, and 99.5 percent for partic...

Ngày tải lên: 12/08/2014, 02:20

... R-2 blending processes in, R-2, R-5 to R-6 catalytic cracking in, P-2 to P-3 chemical treating in, R-5 coking processes in, R-4 combining processes in, R-4 conversion process in, R-2 to R-4 cracking processes ... P-14 polymerization in, R-4 rearranging processes in, R-4 separation process in, R-2 solvent extraction in, R-5 sweetening processes in, R-5 tanks and, T -16 treatment process...

Ngày tải lên: 12/08/2014, 01:21

... Vaporizor Applications Armstrong Engineering Associates: see above W Waste Management Environment Canada: see above xx Contributors Process Engineering Equipment Handbook Claire Soares McGraw-Hill New ... 1985. In May 2001 she was appointed to Fellow grade by ASME. Process Engineering Equipment Handbook is her fourth book. The first, Process Plant Machinery, Second Edition,...

Ngày tải lên: 12/08/2014, 02:20

... For illustrative purposes in this handbook, a few specific illustrative examples of applications common to process engineering and some associated technology will be discussed. ... also been estimated. The process configurations, CO conversion rates, CO 2 removal efficiencies and other process parameters are the same as in IEA studies. Almost all process steps are based on ... pressur...

Ngày tải lên: 12/08/2014, 02:20

... on the specific process requirements, such as higher overload capacity, a certain pressure rise to surge, maximum efficiency at design point or rather at a certain part load, the process design ... reduce the starting torque and for part- load operation. In cases where part- load occurs frequently and power is highly evaluated, inlet guide vanes achieve higher part- load efficiencies an...

Ngày tải lên: 12/08/2014, 02:20

... very expensive retrofit engineering or reengineering, especially if major failures or production-loss events have occurred, without any warning provided by the existing system. Process engineers frequently ... is placed, the columns or piles that support the floor, and pipes and tubes in a process plant. A spring then is a part that can flex upon having a force applied and then tend to r...

Ngày tải lên: 12/08/2014, 02:20