Process Engineering Equipment Handbook 2009 Part 13 potx
Process Engineering Equipment Handbook 2009 Part 13 potx
... Gears
Conventional New Design
D (mm) 170 150
B/D 1.0 1.4
p (N/mm
2
) 3.0 2.8
v (m/s) 139 (167) 122 (146)
T
max
(°C) 132 (141) 121 (130 )
Values in parentheses refer to overspeed 120%.
Power Transmission P-123
Hydrodynamic ... provided with an electrical insulation and installed between
the steam turbine and alternator. In this particular case the synchronous clutch
coupling was installed as...
Process Engineering Equipment Handbook 2009 Part 5 potx
... on the specific process requirements, such as higher overload capacity,
a certain pressure rise to surge, maximum efficiency at design point or rather at
a certain part load, the process design ... reduce the starting torque and for
part- load operation. In cases where part- load occurs frequently and power is highly
evaluated, inlet guide vanes achieve higher part- load efficiencies an...
Process Engineering Equipment Handbook 2009 Part 14 potx
... 110 140 201 176 121 12 13 0.073
120 13. 0–25.0 225 120 150 209 205 145 12 16 0.095
130 17.0–33.0 215 130 160 218 214 156 12 17 0.110
140 20.0–40.0 200 140 170 228 225 165 13 20 0.150
150 23.0–46.0 ... GmbH.)
151
P-202 Power Transmission
FIG. P- 213 Process control circuit. (Source: J. M. Voith GmbH.)
Converter
Indicator
As with the speed (rpm), a process value (e.g., pressure,...
Process Engineering Equipment Handbook 2009 Part 20 ppt
... P-128
blades in, P-123, P -138
boiler feed pumps use of, P-152 to P-164
characteristics of, P -134 to P -136
converter circuit in, P -138
cost of operation of, P -137 to P -138
coupling selection for, ... in, P -138
scope for varying characteristics in, P -138
speed regulation using, P-155 to P-164
torque converter in, P-123 to P-127, P -134
to P -136 , P-166 to P-184
torque in, P-128,...
Process Engineering Equipment Handbook 2009 Part 1 ppsx
... Vaporizor Applications
Armstrong Engineering Associates: see above
W
Waste Management
Environment Canada: see above
xx Contributors
Process Engineering
Equipment Handbook
Claire Soares
McGraw-Hill
New ... 1985. In May 2001 she was appointed to
Fellow grade by ASME.
Process Engineering Equipment Handbook is her fourth book. The first, Process
Plant Machinery, Second Edition,...
Process Engineering Equipment Handbook 2009 Part 2 pdf
... Filsorption II process) is used for separation
of submicron particles, heavy metals, and toxic hydrocarbons by a combination of
filtering, “sorption,” and chemical reaction.
The Wetpac
®
process is ... (sodium chloride) is the main offender.
In the cold parts of the engine it is the sodium chloride that does the damage,
whereas in the hot parts of the engine it is sodium sulfate (or sulfidiz...
Process Engineering Equipment Handbook 2009 Part 3 doc
... For illustrative purposes in this handbook, a few specific illustrative examples of
applications common to process engineering and some associated technology will be
discussed. ... also been estimated.
The process configurations, CO conversion rates, CO
2
removal efficiencies and
other process parameters are the same as in IEA studies. Almost all process steps
are based on ... a CO
2...
Process Engineering Equipment Handbook 2009 Part 4 pdf
... where process gas is permitted in the
open distance piece (e.g., for O
2
, N
2
, CO
2
, process air, etc., generally in the industrial gas industry).
(Source: Sulzer-Burckhardt.)
Compressors C- 113
Consists ... of a very small number of parts
Is made of solid metal without any plastic material
Avoids permanent mechanical friction
Avoids contamination or fouling of the process g...
Process Engineering Equipment Handbook 2009 Part 6 pps
... very expensive retrofit
engineering or reengineering, especially if major failures or production-loss events
have occurred, without any warning provided by the existing system. Process
engineers frequently ... is placed, the columns or piles that support the floor,
and pipes and tubes in a process plant. A spring then is a part that can flex upon
having a force applied and then tend to r...
Process Engineering Equipment Handbook 2009 Part 7 pdf
... Rigid supports and a flexible rotor.
13
FIG. C-349B Flexible supports and rigid rotors.
13
TABLE
C-29 Characteristics of Forced and Self-Excited Vibration
13
Forced or Self-excited or
Resonant ... Buscarello, R., vibration course notes, 1980.
19. Handbook on vibration, McGraw-Hill, New York.
20. Bloch, H., and Soares, C. M., Turboexpanders and Process Application, Gulf Professional P...