Process Engineering Equipment Handbook 2009 Part 10 pdf
Process Engineering Equipment Handbook 2009 Part 10 pdf
... removal efficiency: 100 percent for particles of 8 microns and larger, 99 percent for particles of 6 to 8 microns, 90 percent for particles of 4 to 6 microns, and 85 percent for particles of 2 to ... liquid removal efficiency of 100 percent for particles 3 microns and larger, and 99.98 percent for particles less than 3 microns. Solids removal efficiency: 100 percent for particles of 3 microns...
Ngày tải lên: 12/08/2014, 02:20
Process Engineering Equipment Handbook 2009 Part 2 pdf
... the sterilization process. Compression produces work, which, in turn, produces heat that also can contribute to sterilization. A -102 Air Purification; Air Sterilization FIG. A -103 Unit for separating ... Filsorption II process) is used for separation of submicron particles, heavy metals, and toxic hydrocarbons by a combination of filtering, “sorption,” and chemical reaction. The Wetpac ®...
Ngày tải lên: 12/08/2014, 02:20
Process Engineering Equipment Handbook 2009 Part 4 pdf
... below the limit where some of the common engineering Compressors C-121 FIG. C -106 The labyrinth piston. (Source: Sulzer-Burckhardt.) C-122 Compressors FIG. C -107 The compressor valve. (Source: Sulzer-Burckhardt.) Compressors ... loaded parts, to optimize the aerodynamic characteristics, to influence the movement of the dynamic parts, to introduce improved materials and manufacturing techni...
Ngày tải lên: 12/08/2014, 02:20
Process Engineering Equipment Handbook 2009 Part 7 pdf
... performance curves showing a 10 percent safety margin established at design ratio, and 10 percent safety margin at the highest ratio (FIG. C-385). Calibration of 10 percent at design ratio results ... Buscarello, R., vibration course notes, 1980. 19. Handbook on vibration, McGraw-Hill, New York. 20. Bloch, H., and Soares, C. M., Turboexpanders and Process Application, Gulf Professio...
Ngày tải lên: 12/08/2014, 02:20
Process Engineering Equipment Handbook 2009 Part 16 pdf
... 150 to 255 mm to 230 m 3 /h to 60 m to 70 bar to 205°C to 3600 rpm U.S. units 6 to 10 in to 100 0 gpm to 200 ft to 100 0 psi to 400°F to 3600 rpm TABLE P-42 VCR8 Pumps Design Criteria Bowl Sizes Capacity ... specifications. These processes are discussed in more detail in the following subsections. A simplified flow diagram of the various refinery processes and products is provided in Fig. R-1...
Ngày tải lên: 12/08/2014, 02:20
Process Engineering Equipment Handbook 2009 Part 20 ppt
... C-413 governors dead band in, T -102 electrohydraulic, T -104 to T -106 extraction type, T -106 mechanical, T -101 to T -102 mechanical-hydraulic, T -102 to T -104 steam turbines and, T -100 to T -108 grade of abrasives, ... gears, P-98 to P -107 axial tilting pad bearings in, P -104 to P -107 back-to-back test bed for, P-99 to P -101 deformation analysis in, P -102 , P -104 design...
Ngày tải lên: 12/08/2014, 01:21
Process Engineering Equipment Handbook 2009 Part 1 ppsx
... In this case, PWL dB re. pW 0 = Ê Ë ˆ ¯ () 10 1 10 log W W SIL dB re. 1pW m 0 2 = Ê Ë ˆ ¯ () 10 10 log I I SPL dB re. Pa 0 = Ê Ë ˆ ¯ ¥ () - 20 2 10 10 5 log P P Acoustic Enclosures, Turbine A-15 FIG. ... 1985. In May 2001 she was appointed to Fellow grade by ASME. Process Engineering Equipment Handbook is her fourth book. The first, Process Plant Machinery, Second Edition, wa...
Ngày tải lên: 12/08/2014, 02:20
Process Engineering Equipment Handbook 2009 Part 3 doc
... (precalciner 40–70% 610 1,250 1,220–1,690 None Potential for NH 3 , kilns) PM 10 emissions SCR Low (all types of 70–90% 3,150– 4,840–7,500 None Potential for NH 3 , kilns) 10, 050 PM 10 emissions; SO 3 may ... For illustrative purposes in this handbook, a few specific illustrative examples of applications common to process engineering and some associated technology will be discusse...
Ngày tải lên: 12/08/2014, 02:20
Process Engineering Equipment Handbook 2009 Part 5 potx
... 630 710 710 a 800 900 1,000 1 ,100 1,200 1,400 1,600 1,800 2,000 b 300 350 400 450 500 600 700 800 900 H 1 4,800 5,600 5,400 5,700 7,200 7,750 8,700 9,900 11,000 H 2 6,700 8,200 7,400 7,900 10, 100 ... 100 RIK 112 RIK 125 RIK 140 A 4,600 4,480 5,900 6,500 6,700 7,230 8,450 9,300 10, 400 B 3,800 4,000 4,200 4,400 4,900 5,270 5,750 6,200 6,500 C 3,400 4 ,100 3,700 4,000 5,700* 6,600* 7,300...
Ngày tải lên: 12/08/2014, 02:20
Process Engineering Equipment Handbook 2009 Part 6 pps
... Ø g-s, 1 0.0311 0.00259 0.0 0102 0 .102 g ft/s 32.16 1 0.0833 0.0328 3.28 ft/s 2 in/s 386 12.0 1 0.3937 39.37 in/s 2 cm/s 980 30.48 2.540 1 100 cm/s 2 m/s 9.80 0.3048 0.0254 0. 010 1 m/s 2 Ø TABLE C-19 ... very expensive retrofit engineering or reengineering, especially if major failures or production-loss events have occurred, without any warning provided by the existing system. Proces...
Ngày tải lên: 12/08/2014, 02:20