Plastics Technology Handbook 2011 Part 14 pps
Handbook of Plastics, Elastomers and Composites Part 14 pps
... nuts, and clips. They rarely are used in pretapped holes. Figure 8 .14 shows correct and incorrect methods of mechanical fastening of plastic parts using this hardware. Inserts into the plastic part ... be taken because of the nature of the substrate and possible interactions with the adhesive or the environment. The following sections identify some of these considerations...
Ngày tải lên: 10/08/2014, 12:21
Modern Plastics Handbook 2011 Part 6 pps
... 3.2 to 6. 4 mm (0.125 to 0.250 in). 1 06 As illustrated in Fig. 5.44, 103 slitters (or trim- mers) are also required to remove the edge bead in many film and sheet 5 .66 Chapter Five 0 267 1 46_ Ch05_Harper ... — 64 75–200 Ͻ900 — 89 150–380 60 0–1520 61 0–1220 114 Ն220 900–1830 915–2290 152 Ն220 1520–3050 1370–3550 203 — — Ն4 065 0 267 1 46_ Ch05_Harper 2/24/00 4:55 PM Page 5 .61 inje...
Ngày tải lên: 11/08/2014, 16:22
Modern Plastics Handbook 2011 Part 7 ppsx
... Books, Boston, 1 972 , p. 222. 114. Strong, A. B., Plastics, p. 295. 115. Ibid., pp. 2962 97. 116. Petrotheneđ Polyolefins, p. 84. 1 17. Berins, M. L., Plastics Engineering Handbook, p. 1 17. 118. Wire ... Monitor Cavity Filling Pressure,” ANTEC’ 97, 19 97, p. 3659. 172 . Mueller, N., private correspondence, 1999. 173 . C-Mold Design Guide, p. 144. 174 . Belofsky, H., Plastics: Pro...
Ngày tải lên: 11/08/2014, 16:22
Modern Plastics Handbook 2011 Part 9 pps
... combination. In October 199 8, Moldflow released a family of products called MPX (Moldflow Plastics Xpert). The Moldflow Xpert Series is the down- stream realization of Moldflow’s Process Wide Plastics Simulation Strategy ... position is at the end of the part. Most of the part has a high confidence of fill. However regions far from the gate are shown in yellow, while areas at the end...
Ngày tải lên: 11/08/2014, 16:22
Plastics Technology Handbook 2011 Part 1 potx
... conduct. (cal/s–cm–K !10 4 ) C177 8.0 11 12 2.8 12 . Specific heat (cal/g–K) — 0.55 0.55 0.46 13 . Linear therm. exp. coeff. (K K1 !10 5 ) D696 10 –22 11 13 8 .1 10 .0 14 . Continuous-use temperature (8C) — 80 10 0 12 0 12 0 16 0 15 . Deflection ... 38–49 60–88 10 7 12 1 16 . Volume resistivity, ohm cm D257 O10 16 O10 16 O10 16 17 . Dielectric constant at 1 kHz D150 2.25–2...
Ngày tải lên: 12/08/2014, 01:22
Plastics Technology Handbook 2011 Part 5 potx
... Finishing Structure Press Trimming Drilling Bonding Fastening Autoclave Oven/bag Automatic cutting Hand lay-up Tape laying Tape winding Thickness 100 50 0 μm Width 50 0– 150 0 mm Resin contents 30 %–60 % Kevlar Glass Carbon Boron Others STD weaves Bias weaves Triaxial Hybrids Fibers Resin systems Epoxy Tape Thickness 50 –300 μm Width 25 1200 ... thermoforming, slush molding, and spinning....
Ngày tải lên: 12/08/2014, 01:22
Plastics Technology Handbook 2011 Part 7 ppsx
... contact with foods or where phenol or resorcinol would be otherwise objectionable. 2-112 Plastics Technology Handbook q 2006 by Taylor & Francis Group, LLC ... involves a study of the specific properties of plastics which dictate their applications. Besides the relative ease of molding and fabrication, many plastics offer a range of important advantages ... engineer be aware o...
Ngày tải lên: 12/08/2014, 01:22
Plastics Technology Handbook 2011 Part 8 ppt
... flow. Air bearing Transducer Transducer Amplifiers Recorders Torsional spring Constant speed motor Gear assembly Bearing FIGURE 3.34 Scheme of a Weissenberg Rheogoniometer. 3-44 Plastics Technology Handbook q 2006 by Taylor & Francis Group, LLC TABLE 3 .8 Heating Tests of Some Common Polymers Polymer Color of ... smell Burns in flame, self extinguishing slowly on removal; black resi...
Ngày tải lên: 12/08/2014, 01:22
Plastics Technology Handbook 2011 Part 12 pdf
... 1964. Aminoplastics, Iliffe, London, UK. 48. Phillips, L. N. and Parker, D. B. V. 1964. Polyurethanes: Chemistry, Technology and Properties, Iliffe, London, UK. 4-160 Plastics Technology Handbook q ... 2005. Polym. Int., 54, 981. 40. Kohan, M. I. ed. 1973. Nylon Plastics, p. 201. Wiley, New York. 41. Nelson, W. E. 1976. Nylon Plastics Technology, Newnes-Butterworths, London, UK. 4...
Ngày tải lên: 12/08/2014, 01:22
Plastics Technology Handbook 2011 Part 16 pptx
... opportunities for plastics products [11–15]. It is next only to the packaging industry in order of importance as a user of plastics, and has proved to be the fastest growing market for plastics use ... for almost half of this industry’s total consumption of resins. The largest PVC 7-10 Plastics Technology Handbook q 2006 by Taylor & Francis Group, LLC ... construction produc...
Ngày tải lên: 12/08/2014, 01:22