Refrigeration and Air Conditioning 3 E Part 12 pps

... condensation or ice on cold surfaces. 34 .6 Excess condenser pressure This is the greatest cause of excess power and loss of duty in a refrigeration system. Causes are: 33 0 Refrigeration and Air- Conditioning 31 .6 ... the process exceeds the load. (See Figure 31 .2.) The range of the control will therefore be the differential of the detector plus the upper and lower oversho...

Ngày tải lên: 12/08/2014, 00:20

... hygiene, or the cheese will be damaged. Some cheeses can be frozen for long-term storage, but must then be allowed to thaw out gradually and complete their ripening before release to the market. Other ... plate freezers. Health and safety requirements continue to become stricter in the maintenance of the cold chain and the latest regulations should be adhered to. 178 Refrigeration an...

Ngày tải lên: 12/08/2014, 00:20

... sides of the fan. Such treatment needs to be selected for the particular application regarding frequency of the generated noise and the degree of attenuation required, and competent suppliers ... connecting the inner and outer tappings to the ends of the manometer, the difference will be the velocity pressure. Figure 27.2 Vertical and inclined manometers Figure 27 .3 Pitot tube Sensi...

Ngày tải lên: 12/08/2014, 00:20

... higher condensing temperature will be a drop in the refrigerating effect, since the liquid enters the expansion valve hotter, and a decrease in volume pumped due to the lower volumetric efficiency. ... separate budgets, possibly accounted for by four different managers, so these budgets need to be adjusted. Separate fuel meters are needed to prove the savings, which might otherwise be held...

Ngày tải lên: 12/08/2014, 00:20

... Maintenance. Service. Fault-finding. Training 33 8 34 Efficiency and economy in operation 35 1 35 Catalogue selection 35 7 Appendix Units of measurement 36 7 References 36 9 Index 37 3 vi Contents The refrigeration ... determined by the requirements of the air conditioned enclosure. BS 56 43: 1984 The refrigeration cycle 23 Low-temperature compressor Low-temperature condense...

Ngày tải lên: 12/08/2014, 00:20

... contributes CO 2 emission to the atmosphere. The choice of refrigerant is therefore about the efficiency of the refrigerant and the efficiency of the refrigeration system. The less the amount of energy ... copper. This chapter is about the new refrigerants and the new attitude needed in design, maintenance and servicing of refrigeration equipment. 3. 2 Ideal properties for a refri...

Ngày tải lên: 12/08/2014, 00:20

... covered by the provisions of BS.4 434 :1980 and require safety pressure relief devices as outlined in Section 6.10. In cases where there is no shut-off valve between the condenser and receiver, ... the condenser heat. If the mass flow is reduced, the temperature rise must increase, raising the condensing temperature and pressure to give lower plant efficiency. In practice, the temperatu...

Ngày tải lên: 12/08/2014, 00:20

... and shorten the working life. 11.11 Site pressure safety tests Site-erected pipework, once complete, must be pressure tested for safety and freedom from leaks. Pressures will be 1 .3 times the 118 Refrigeration ... permit their use elsewhere. Table 10.2, based on the tentative temperature differences of 15 K and 12 K 122 Refrigeration and Air- Conditioning plant will not b...

Ngày tải lên: 12/08/2014, 00:20

... have to be installed on site. 13. 3 One-piece packages The true packaged unit will have all the parts of the system and will be factory tested in the complete state. There are four basic types: 25°C 30 °C 35 °C 40°C ... a eutectic solution, and these are frozen down by placing these elements in the domestic deep-freeze cabinet. Once frozen, they can be used in picnic baskets, etc., for...

Ngày tải lên: 12/08/2014, 00:20

... are based on observed practice. The parameters are the size of the store, the enthalpy difference between inside and outside air, and the usage of the doors. The latter is affected by the existence ... process analysed to decide representative rates. Assumptions should be stated and agreed by the parties concerned, since these estimates are to form the basis for the selection of the re...

Ngày tải lên: 12/08/2014, 00:20