Thumb for Mechanical Engineers 2011 Part 9 doc

... 6(2), A 49- A53, 193 9. 18. Zaretsky, E. V. (Ed.), STLE Life Factors for Roller Bearings. Society of Tribologists and Lubrication En- gineers, 199 2. 258 Rules of Thumb for Mechanical Engineers ... Rules of Thumb for Mechanical Engineers Resonance: When the frequency of the excitation force (forcing function) is equal to or very close to the natural fre...

Ngày tải lên: 11/08/2014, 21:21

... 1 89 Transportation Pipe Lines 190 Steel Pipe Design 190 Gas Pipe Lines 190 Liquid pipe Lines 192 Pipe Line Condition Monitoring 195 Pig-based Monitoring Systems 195 ... Stress and Strain 295 Introduction 295 Definitions4tress and Strain 295 Equilibrium 297 Compatibility 297 Saint-Venant’s Principle 297 Superposition 298...

Ngày tải lên: 11/08/2014, 21:21

... Transfeel; 16: Houston: Gulf Publishing Co., 198 4. Prog., 45: 394 8, 194 9. ASME, 70: 695 , 194 8. 347-358, 197 3. 52 Rules of Thumb for Mechanical Engineers THERMODYNAMIC ESSENTIALS Thermodynamics ... (bsfc): fuel rate in lbrn/hr bsfc = bhP 68 Rules of Thumb for Mechanical Engineers Single MECHANICAL SEAL CLASSIFICATIONS Multiple Mechanical seal...

Ngày tải lên: 11/08/2014, 21:21

... 4. 79 5.55 6.58 8.02 10.1 13.2 18.3 27 .9 51.0 161.0 3400 2 .98 2 .93 2 .93 2 .99 3. 09 3.26 3. 49 3.80 4.22 4.78 5.53 6.54 7 .96 9. 98 13.0 17 .9 27.1 48.6 138.1 3600 2 .97 2 .92 2 .93 2 .98 ... 3.34 3.58 3 .91 4.35 4 .96 5.78 6 .91 8.53 10 .9 14.8 21 .9 1800 3.05 2 .99 3.00 3.05 3.16 3.33 3.57 3 .90 4.34 4 .94 5.75 6.87 8.47 10.8 14.6 21.2 36 .9 2000...

Ngày tải lên: 11/08/2014, 21:21

... 100 150 .99 0 1.00 1.00 1.00 1.00 1.00 1.00 1.00 .98 0 ,98 5 ,99 0 ,99 5 1.00 1.00 1.00 1.00 .98 0 .a65 370 .geO .WO 1. 09 1.00 1.00 . 890 .90 0 -820 -94 0 .o(M -98 0 .SSO ... Factors Spur 10 1 to1 . 299 P 299 G 3tol .315P .407 G 5tol .319P .434 G Number of Teeth 20 2s 30 .333P .359P .388P .333G .359G .WG .351 P .3 79 P .4 09 P...

Ngày tải lên: 11/08/2014, 21:21

... .I 09 1. 097 1.404 40 40s Std. .I 33 1.0 49 1.6 79 80 80s Ex. Hvy. .I 79 .95 7 2.1 72 160 .250 .815 2.844 XX Hvy. .358 . 599 3.6 59 196 Rules of Thumb for Mechanical Engineers ... 140 160 .562 .688 .96 9 1.2 19 1.531 1.81 2 2.062 2.344 22.876 22.626 22.064 21.564 20 .93 8 20.376 19. 876 19. 314 140.68 171. 29 238.35 296 .58 3...

Ngày tải lên: 11/08/2014, 21:21

... 287 Forming 288 Casting 2 89 Case Studies 290 Failure Analysis 290 Corrosion 291 References 292 2 59 264 Rules of Thumb for Mechanical Engineers Table 4 wpical Mechanical ... Rules of Thumb for Mechanical Engineers Resonance: When the frequency of the excitation force (forcing function) is equal to or very close to the natural...

Ngày tải lên: 11/08/2014, 21:21

... 90 1.3 (-3 Ex&rnal surface WRLength (4 0.0 598 0.0 598 0.0 598 0.0 598 0.0 798 0.0 798 0.0 798 0.0 798 0.1 197 0.1 197 0.1 197 Table 9 Thermal Conductivities of Materials of Construction ... 14.83 15.75 16.56 18. 59 19. 86 21 18 22.10 31. 29 32.56 33.88 nm (m) Internal Area 143.8 172 .9 194 .8 215.5 271.6 3 09. 0 352.3 383.2 7 69. 0 83...

Ngày tải lên: 11/08/2014, 21:21

... Standards ( 199 0) 40 90 1 .oo 4 97 0.44 L2 98 0.33 4 99 0.21 L5 95 0.62 4 96 0.53 since they are based on material cleanliness at the time. In addition, special processing for some ... 2.1 09 x .520 x 65,000 = 4. 799 Pd = 390 ,000 x 350 x 2.05 From Equation 26 the actual diametral pitch at the large end of the pinion is: = 3 .99 1 4.485 x...

Ngày tải lên: 11/08/2014, 21:21

... 00 540 661 795 1.005 m 502 613 738 875 93 5 m 4 69 874 440 8 19 571 687 816 1,064 m 536 642 762 894 99 7 m 414 504 603 715 8 39 974 770 93 8 1,124 391 475 5 69 673 7 89 916 1,053 727 ... 1,186 520 608 864 99 4 817 94 0 1,073 774 891 1,017 1,152 737 846 96 6 1, 095 703 806 91 9 1,042 03 1,442 m 1,373 a, 562 684 8 19 968 1.131 1.3 09 1,5 09 m 83 1...

Ngày tải lên: 11/08/2014, 21:21