Theory and Design of CNC Systems Part 11 pdf
Theory and Design of CNC Systems Part 11 pdf
... mentioned, the software design of a CNC system must be done to-
gether with the design of the hardware and the operating system. As the design of
the software architecture belongs to the stage of developing ... processor and memory were assigned
for each function. Therefore, the former CNC systems were closed systems, in which
the design of the CNC system depend...
Theory and Design of CNC Systems Part 14 potx
... 187
ADCBI, 107, 108, 128–155, 187, 211
ADCBI-type NCK – architecture, 211
address, 237
aging, 328
AGV, 4
AIM, 404
and – AND, 260
and not – ANDN, 261
and stack – ANDS, 266
application layer, 275
approximation ... function, 56
soft bus, 30, 416
soft PLC, 247–249
soft real-time system, 319
Soft-NC, 30, 248, 353, 355, 357, 359, 362–364,
366–369, 372–377, 388, 392, 393, 416
software model...
Theory and Design of CNC Systems Part 1 pps
... 410
11. 5.1 Part Programming for the Milling Operation . . . 411
11.5.2 PartProgrammingfortheTurningOperation 414
11. 6 STEP-CNCSystem 415
11. 6.1 TypesofSTEP -CNC 417
11. 6.2 Intelligent STEP -CNC Systems ... Open CNC 353
10.1 Introduction . . 353
10.2 DesignofSoftwareArchitecture 356
10.2.1 CNCSystemModeling 356
10.3 DesignofSoft-NCSystem 359
10.3.1 Design of Task Module ....
Theory and Design of CNC Systems Part 2 doc
... detailed functions of any
particular CNC.
2.2 Part Program
Although the standard exists for generating a CNC part program, sequentially listing
the commands for executing CNC, each CNC maker has, ... representative indicator
that shows the design concept and the functional aspect of a CNC and is a big part of
33
26 1 Introduction to NC Systems
System
memory
Part...
Theory and Design of CNC Systems Part 3 ppsx
... the interpreter of the CNC system is the soft-
ware module of the NCK unit that interprets the part program consisting of G&M-
code commands and related addresses such as S, T, and F. The interpreter ... understand the structure of a part pro-
gram and the commands used therein.
In a CNC system, various coordinate systems, such as the machine coordinate
system, work...
Theory and Design of CNC Systems Part 4 potx
... number
of the pulses from rough interpolation and Acc/Dec control at time i. t
ipo
is the it-
eration time of rough interpolation and N is the ratio of the iteration time of rough
interpolation and ... 4
Acceleration and Deceleration
In order to smooth the movement of a machine, the acceleration and deceleration for
the movementof the machineaxes should be controlled. For...
Theory and Design of CNC Systems Part 5 potx
... Acceleration and Deceleration
trajectory is inversely proportional to the feedrate and sudden changes of feedrate
result in reduction of accuracy of the CNC equipment.
In the ADCBI type of NCK, the ... connected it is possible to classify pairs of blocks into twelve types
depending on the type of block (e.g. normal block and short block) and the difference
of commanded...
Theory and Design of CNC Systems Part 6 pptx
... execution algo-
rithms and implementation by pseudo-code. In this chapter, only the design of NCK
will be described and the overall design of the CNC system where the PLC and MMI
units are included ... reference on design of digital drive
systems.
Figure 5.14 shows the architecture of a speed feedforward controller where the posi-
tion command,
α
w
,isfiltered and the...
Theory and Design of CNC Systems Part 8 ppsx
... standard
IEC1131, is the international standard for PLC, consisting of five parts and IEC1131-
3 is one of the parts of which IEC1131 is composed.
1. IEC1131-1: PLC General information.
2. IEC1131-2: ... Soft NC, Soft NC and
Soft PLC can be regarded as the same system. Soft PLC which is made by a user
interface and the PLC kernel based on the IEC1131-3 can be regarded as partial
s...
Theory and Design of CNC Systems Part 9 potx
... task
is called CNC programming.
8.3.1 The Sequence of Part Programming
Roughly, CNC programming is composed of the generation of a process plan from
a part drawing and the generation of the part program. ... used on the shop floor and has a good effect on
productivity. In this text book, the design and development of Shopfloor Oriented
Programming systems embedded...
Từ khóa:
- design and development of aircraft systems an introduction pdf free
- theory and design of electrical and electronic circuits pdf
- 3 theory and design of optical thin film coatings
- theory and application of spread spectrum systems
- design and development of aircraft systems
- design and development of aircraft systems download
- design and development of aircraft systems moir pdf
- design and development of aircraft systems 2nd edition