The Motor Vehicle 2010 Part 6 ppsx

... flat bimetal thermostat spring. It senses the temperature of the body of the carburettor and regulates Fig. 11. 26 Stromberg CD carburettor 408 The Motor Vehicle to the underside of the air valve ... pump 380 The Motor Vehicle bleed hole in the plug in the end of the passage delivering the fuel to the emulsion tube not only helps to emulsify the extra fuel s...

Ngày tải lên: 11/08/2014, 20:21

... Ltd) 62 6 The Motor Vehicle are nominally in contact, they are in fact held apart by the peaks of their microscopic roughness. A proportion of these peaks pressure-weld together, while others ... at – 15 5 .6 – 20W 4500 at – 10 5 .6 – 25W 60 00 at – 5 9.3 – 20 – 5 .6 9.3 30 – 9.3 12.5 40 – 16. 3 16. 3 50 – 16. 3 21.9 60 – 21.9 26. 0 Fig. 18.2. At 100°C, the two reference oils...

Ngày tải lên: 11/08/2014, 20:21

... over the end of the stem, seating its rim on the retainer washer for the spring, so that there is a small clearance between the tip of the stem and the other end of the thimble. When the cam ... camshaft. The exhaust valves are inclined 16 to one side of the axis of the cylinder and the inlets 19° to the other side. Their seats are in a penthouse-type combusti...

Ngày tải lên: 11/08/2014, 20:21

... 1985. 1 96 200 180 160 80 70 60 50 40 30 120 100 80 60 580 560 540 220 110 100 90 80 70 60 50 40 The Motor Vehicle 420 Engine speed (rev/min) 1000 1200 1400 160 0 1800 ... 2400 260 0 581 N m (429 lbf ft) 134 kW (180 bhp) 280 64 kW ( 86 bhp) 266 N m (1 96 lbf ft) 262 N m (193 lbf ft) 65 kW (87 bhp) 2800 rev/min 240 1000 1200 1400 160 0 1800 2...

Ngày tải lên: 11/08/2014, 20:21

... to supplement the capacity of the common rail. 6. 47 The Bosch system As can be seen from Fig. 6. 57, the fuel is lifted by the low pressure pump in the tank, through a filter to the roller cell ... lines 6 on the rotor head. The ends of the adjustment plate limit the outward movement of the plungers, and therefore the maximum 1 2 3 4 5 Fig. 7.20 This anti-st...

Ngày tải lên: 11/08/2014, 20:21

... pulley on the front end of the crankshaft. On the other hand, the oil pump is interposed between the toothed wheel for the HTD drive and the crankcase wall and driven by a gear on the crankshaft. ... HTD toothed belt drive from the crankshaft to the injection pump and overhead camshaft. The alternator on the side of the crankcase, and the spindle of the fan an...

Ngày tải lên: 11/08/2014, 20:21

... coaxially but with their cranks at 90° to each other, are the most common layouts. Their firing orders are 1 5 2 6 4 8 3 7 and 1 6 2 8 4 3 7 5 458 The Motor Vehicle the torque of the engine can be ... senses the passage of either a pin or hole in the flywheel. These two signals are processed in the control unit to make them compatible with the computer. The parameter...

Ngày tải lên: 11/08/2014, 20:21

... If the accelerator pedal is further depressed the balance will be upset and the valve will move to the left, the part C will then uncover the inlet port from the pump and the pressure in the ... On the other hand, if the accelerator pedal is released a little then the oil pressure on the left-hand end of the valve will move the valve to the right, thus uncove...

Ngày tải lên: 11/08/2014, 20:21

... B is thus the fixed member of the epicyclic train, the gear A is the driving member and the planet carrier and wheel are thus driven at half the speed of the halfshaft. 884 The Motor Vehicle 31.7 ... equal to P/2. The reactions of the forces acting on the ends of the beam act on the discs, hence equal forces are applied to the discs at equal distances from thei...

Ngày tải lên: 11/08/2014, 20:21

... that other things being equal the smaller the height OG the less the overturning couple. The magnitude of the righting couple QQ is Q × SS, so that the greater the wheelbase SS the less the force ... positions 9 46 The Motor Vehicle 36. 12 Improvement of active safety Active safety embraces the ergonomic design of the vehicle for ease of control by the drive...

Ngày tải lên: 11/08/2014, 20:21