Manual Gearbox Design Part 1 pot

... Gearbox casing Materials guide 38 38 39 39 40 46 50 52 53 54 61 66 66 67 67 80 82 83 84 88 96 10 0 10 6 11 3 11 3 11 3 11 7 1 30 13 4 13 4 13 5 13 7 13 7 13 9 14 1 14 3 ... 11 7 1 30 13 4 13 4 13 5 13 7 13 7 13 9 14 1 14 3 14 8 15 0 15 2 15 5 15 7 15 8 Index 16 1 Contents Preface Acknowledgements Introduction 1 Crown wheel...

Ngày tải lên: 11/08/2014, 13:22

... between the engine, gearbox and other surrounding components. 8 Manual Gearbox Design K, =load distribution factor: pinion overhung mounted, 1. 10 pinion straddle mounted, 1 .OO axle-drive ... pinion torque T, (calculated in 1b.in or kg.m): 18 Manual Gearbox Design (e) Equiv. twisting moment due to combined twisting and bending: nd3 - x4 16 3 Angle of to...

Ngày tải lên: 11/08/2014, 13:22

... hardening. 8 Poor mounting and casing design. 9 Surface damage in final machining or grinding operation. 10 1 1 Excessive operating temperatures. 12 Malalignment of mountings. which breaks ... bearings (g) the transmission casing design and material in any particular transmission design. The transmission unit consists of four main components or units: 1 The gears and shaf...

Ngày tải lên: 11/08/2014, 13:22

... 0 .10 3 0 .10 7 0 .11 0 0 .11 3 0 .11 8 0 .12 2 0 .12 6 0.068 0.074 0.078 0.082 0.086 0.090 0.093 0.098 0 .10 2 0 .10 6 0 .10 9 0 .11 2 0 .11 7 0 .12 1 0 .12 5 0.0 71 0.078 0.082 0.087 0.09 1 0.095 ... Figure 5.9(a) and 98 Manual Gearbox Design Table 5.6 17 t” u = 20” u = 222 ZN Tooth profile 3 Tooth profile 1 Tooth profile 1 10 11...

Ngày tải lên: 11/08/2014, 13:22

... 10 10 -10 November 19 99 10 10-6 Auxiliary Passing Lane 10 10 -11 November 19 99 10 10-7 Slow Moving Vehicle Turnout 10 10 -12 November 19 99 10 10-8 Typical Emergency Escape Ramp 10 10 -13 November 19 99 10 10-9 ... December 19 98 11 40 -1 Standard Noise Wall Types 11 40-3 December 19 98 Contents Design Manual Page 10 Metric Version May 20 01 Date 11 40 Noise Barriers...

Ngày tải lên: 10/08/2014, 20:20

... time- domain O-QPSK O-QPSK O- QPSK Group PPM Range 10 0m 10 m <5m 10 m 10 m <250m 3 -10 m Rate <54Mbps 1Mbps 20Kbps, 250Kbps, 10 Mbps 250Kbps 250Kbps 250Kbps < ;10 Mbps Power High Low Ultra low Very low ... chapter 14 , pp. 293–320. ZigBee Alliance (n.d.). http://www.zigbee.org. Type IEEE 802 .11 b/g Bluetooth UWB-IR IEEE 802 .15 .4 Zigbee Wireless HART IEEE 802 .15 .6 a Band...

Ngày tải lên: 20/06/2014, 12:20

... rule of the birth-death process in Figure 1c “rate up equals rate down” (Cooper, 19 81) as follows (α(n i )λ n,i +λ h,i ) p(n i )=n i +1 μ i p(n i +1 ). Solving the global balance equation, ... MobileandWirelessCommunications:Networklayerandcircuitlevel design1 4 19 97; Floyd, 19 96). Most CAC schemes employed in CDMA systems are designed according the measurement-base...

Ngày tải lên: 21/06/2014, 14:20

... Press, 19 91 16 . D.A. Garvin, Competing on the Eight Dimensions of Quality, Harvard Business Review, Nov/Dec 19 87, p 10 1 -10 9 17 . R.C. Camp, Benchmarking, ASCQ Quality Press, 19 89 18 . F.G. ... Press, 19 91 16 . D.A. Garvin, Competing on the Eight Dimensions of Quality, Harvard Business Review, Nov/Dec 19 87, p 10 1 -10 9 17 . R.C. Camp, Benchmarking, ASCQ Quality...

Ngày tải lên: 10/08/2014, 13:20

... (a) 19 05 (b) 19 50 (c) 19 85 (d) 19 97 Fig. 1. 3 Vacuum cleaners: (a) The hand-powered bellows cleaner of 19 00, largely made of wood and leather. (b) The cylinder cleaner of 19 50. ... cleaners Forty, A. (1 986) Objects ofDesire: Design and Society since 17 50, Thames and Hudson, London, p. 17 4 et seq. 6 Materials Selection in Mechanical Design Table 1....

Ngày tải lên: 11/08/2014, 02:21

... stages of the gearbox design and designed to cater for the particular gearbox application, the loads expected on the gears and the life and efficiencies required from the gearbox. It is only ... x-x- 36 x 17 60 TW Tdriven where RR = rolling radius road wheel (in) Tp = no. of teeth - pinion 34 Manual Gearbox Design companies means that the gear and transmissio...

Ngày tải lên: 11/08/2014, 13:22