Machine Design Databook 2010 Part 17 potx

... max h 2 ¼ 6q 0  2 h 2  1 a 2 þ 1 b 2  2  v a 2 þ 1 b 2  ð27-398Þ ð yz Þ max ¼ 3q 0 2bh  1 a 2 þ 1 b 2  2  1 b 2 þ 2 À v a 2  ð27-399Þ Particular Formula APPLIED ELASTICITY 27.83 Downloaded from Digital Engineering Library @ McGraw-Hill

Ngày tải lên: 11/08/2014, 10:23

... 2029.0 206900 176 Â29 176 Â 26 2.10 1550 159.8 16.3 152.0 15.5 2188.0 2170 00 180 Â30 180 Â 27 2.15 1626 167.7 17. 1 159.9 16.3 2232.0 227600 184 Â30 184 Â 27 2.20 170 2 175 .5 17. 9 166.7 17. 0 2335.9 ... 166.7 17. 0 2335.9 238200 8 Â4 Â 91 186 Â31 186 Â28 1.90 172 7 177 .5 18.1 169.7 17. 3 2377.3 2 5170 0 190 Â32 190 Â 29 1.95 1818 187.3 19.1 178 .5 18.2 2495.8 254500 194 Â33 19...

Ngày tải lên: 11/08/2014, 10:23

... 31.0 Case-hardened machine steel on case-hardened machine steel 4,000 27.5 0.30 C machine steel on cast iron (close-grained) 3,500 24.0 0.40 C machine steel on soft common babbitt 3,000 20.6 Soft machine ... — 0.1 0.9 16.3 81.40 163.0 3.44 0 .176 653.0 0.513 0.2 0.8 7.60 73.70 79.4 3.71 0.320 320.0 0.489 0.4 0.6 2.84 58.99 35.1 4.11 0.534 146.0 0. 417 0.6 0.4 1.08 44.96 17. 6 4.25...

Ngày tải lên: 11/08/2014, 10:23

... 29.7 217 95 40 (50) ( 517) (75.0) (207) (30.0) (40) X 02 Cr 17 Ni 12 Mo 2 0.08 max 1.0 max 2.0 max 10.0/14.0 16.0/18.0 2.0/3.0 0.030 0.045 485 70.3 170 24.7 217 95 40 (50) (483) (70.0) (172 ) (25.0) ... carbon C1015 503 73 317 46 31 71 149 62 1.22 0.048 123 91 Poor C1020 517 75 331 48 31 71 156 62 1 .17 0.046 126 93 Poor C1022 572 83 324 47 27 66 163 62 1 .17 0.046 110 81 Good C1 117...

Ngày tải lên: 11/08/2014, 10:23

... stage. (Note:  and  with initial subscript s designates strength properties of material used in the design which will be used and observed throughout this Machine Design Data Handbook.) SIMPLE STRESS ...  2 ¼ 0 ð2-15Þ  1 ¼ 08 and  2 ¼ 908 ð2-16Þ  max ¼  x 2 ð2 -17  1 ¼ 458 and  2 ¼ 1358 ð2-18Þ Particular Formula STATIC STRESSES IN MACHINE ELEMENTS 2.5 Downloaded from Digital...

Ngày tải lên: 11/08/2014, 10:23

... À120 À145 170 À190 À210 À230 ei À34 À48 À62 À77 À98 À119 À146 174 À208 À242 À271 À299 À327 d9 es À20 À30 À40 À50 À65 À80 À100 À120 À145 170 À190 À210 À230 ei À45 À60 À76 À93 À 117 À142 174 À207 ... Lingaiah, K., and B. R. Narayana Iyengar, Machine Design Data Handbook, Engineering College Cooperative Society, Bangalore, India, 1962. 7. Lingaiah, K., Machine Design Data Handbook, Vol....

Ngày tải lên: 11/08/2014, 10:23

... welds 3.5 4.5 Base metal Toe of machined butt weld 1.2 1.4 Toe of unmachined butt weld 1.5 1.9 Toe of machined end fillet weld with leg ratio 1 : 1.5 2 2.5 Toe of unmachined end fillet weld with leg ... kpsi 2S (pure aluminum) Cold, as received 20 3.0 48 7.0 17S Cold, immediately after quenching 68 10.0 179 26.0 17S Hot, 500–5108C 62 9.0 179 26.0 615–T6 Cold, as received 55 8.0 103 15.0 53S H...

Ngày tải lên: 11/08/2014, 10:23

... 14.  t ¼ F  4 d 2 c 17- 43Þ  c ¼ F  4 ðd 2 3 À d 2 2 Þ 17- 44Þ d 2 > d nom 17- 45Þ  t ¼ 4F d 2 17- 46Þ  t ¼ F ðd 4 À d 2 Þb 17- 47Þ  tn ¼ F bðd 4 À d 2 Þ 17- 48Þ Particular Formula 17. 22 CHAPTER ... 17- 6 and 17- 7, Tables 17- 16 and 17- 17) The mean diameter of pin FIGURE 17- 6 Tapered pin. Sleeve and taper pin joint (Fig. 17- 7) AXIAL LOAD The axial stress induced i...

Ngày tải lên: 11/08/2014, 10:23

... 1:5 Ã 10.00 9.78 15.00 14.57 17. 32 16.32 6.63 6 .17 4.5 0.6 0.3 13.6 M10 Â 1:5 10.00 9.78 16.00 15.57 18.48 17. 43 6.63 6 .17 4.5 0.6 0.3 14.6 M12 Â 1:75 12.00 11.73 18.00 17. 57 20.78 19.68 7.76 7.24 ... Â 1:5 Ã 10.00 9.78 15.00 14.73 17. 32 16.64 6.63 6 .17 4.5 0.6 0.3 M10 Â 1:5 10.00 9.78 16.00 15.73 18.48 17. 77 6.63 6 .17 4.5 0.6 0.3 M12 Â 1:75 12.00 11.73 18.00 17. 73 20.78 2...

Ngày tải lên: 11/08/2014, 10:23

... 1466 1473 1509 1524 1560 1567 1580 5.0 1600 1636 1626 1661 17. 8 1651 1687 1694 À12.5 172 7 176 3 177 0 178 3 177 8 1814 1821 1905 1941 1948 1991 1981 2 017 2024 2032 2068 2057 2093 2101 2113 þ30 2159 2195 ... V-flat 180 1.00 0.75 133 0.87 0.86 177 0.99 0.76 130 0.86 0.86 174 0.99 0.76 127 0.85 0.85 171 0.98 0.77 123 0.83 0.83 169 0.97 0.78 120 0.82 0.82 166 0.97 0.79 117 0.81 0.81 1...

Ngày tải lên: 11/08/2014, 10:23