Industrial Machinery Repair Part 16 pdf

... 5/32 8 /16 5/32 5/32 Lap 3/32 3/32 3/32 8/32 8/32 8/32 1/8 1/8 1/8 5/32 5/32 5/32 5/32 5/32 5/32 3 /16 3 /16 5/32 3 /16 3 /16 5/32 Fillet 8/32 8/32 8/32 1/8 1/8 1/8 1/8 1/8 1/8 5/32 5/32 5/32 3 /16 5/32 ... 5/32 3 /16 5/32 5/32 Corner 3/32 3/32 3/32 8/32 8/32 8/32 1/8 1/8 1/8 1/8 1/8 1/8 3 /16 5/32 5/32 3 /16 5/32 5/32 3 /16 5/32 5/32 Edge 3/32 3/32 3/32 8/32 8/32 8/32 1/8 1/8 1...

Ngày tải lên: 11/08/2014, 08:22

... drives for engines of cars and trucks. G16 Parts of agricultural machinery; individual components of engines (gasoline or diesel) for cars and trucks. G6.3 Parts or process plant machines; marine ... weight is assumed to be part of the shaft’s male portion. The other half is considered to be part of the female portion that is coupled to it. However, when the two rotor parts are sent to a...

Ngày tải lên: 05/08/2014, 11:20

... (5) use of unsuitable lubricants. 7 Chain Drives “Only Permanent Repairs Made Here” Introduction Chain drives are an important part of a conveyor system. They are used to transmit needed power ... are an equal distance apart. Make sure that the shafts are pulled in as close as possible before performing this procedure. The jacking bolts can be used to move the shafts apart evenly after the...

Ngày tải lên: 05/08/2014, 11:20

... design and construction from simple pumps with relatively few parts to extremely complicated pumps with hundreds of indi- vidual parts. Some of the most common components found in centrifugal pumps ... of the rotating impeller impart a radial and rotary motion to the liquid, forcing it to the outer periphery of the pump casing, where it is collected in the outer part of the pump casing call...

Ngày tải lên: 05/08/2014, 11:20

... Ricky. Industrial machinery repair : best maintenance practices pocket guide / Ricky Smith and Keith Mobley. p. cm. ISBN 0-7506-7621-3 (pbk : alk. paper) 1. Machinery Maintenance and repair. 2. Industrial ... Ricky. Industrial machinery repair : best maintenance practices pocket guide / Ricky Smith and Keith Mobley. p. cm. ISBN 0-7506-7621-3 (pbk : alk. paper) 1. Machinery Ma...

Ngày tải lên: 05/08/2014, 11:20

... condition to your supervisor 16 Why should you avoid loose-fitting clothing in the plant? A. It can create a barrier from sharp parts B. It can get caught in moving parts C. It is unprofessional D. ... standards; Introduction: Why Use Best Maintenance Repair Practices? 9 ● The maintenance manager needs to conduct monthly spot checks on randomly selected PMs and repairs for quality assuranc...

Ngày tải lên: 05/08/2014, 11:20

... in machines with moving parts. B. Function as guides. C. Help reduce the friction between moving parts. D. All of the above. 38 Maintenance Skills Assessment C. 3% D. 3 16 inch per ft. of chain 2 ... protrudes above the top of the sheave no more than 1 16 ". B. The belt is flush with the top of the sheave groove. C. The belt is recessed more than 1 16 " into the groove sheave....

Ngày tải lên: 05/08/2014, 11:20

... bearings (e.g., grooved and lobed bear- ings) that incorporates partial arcs. It is necessary to use partial-arc bearing data to incorporate partial arcs in a variety of grooved and lobed bearing configurations. ... grooved bearing. Where the grooved bearing consists of a number of partial arcs with a common center, the lobed bearing is made up of partial arcs whose centers Bearings 97 Figure...

Ngày tải lên: 05/08/2014, 11:20

... design. No foundation should rest partially on bedrock and partially on soil; it should rest entirely on one or the other. If placed on the ground, make sure that part of the foundation does not ... the most maintenance- prone part in the compressor. There are from 8 to 20 vanes on each rotor, depending upon its diameter. A greater number of vanes increase compart- mentalization, which re...

Ngày tải lên: 05/08/2014, 11:20

... Therefore, this valve does not induce turbulent flow in the partially closed position. While the design does not permit exact Compressors 165 Table 8.2 Common failure modes of rotary-type, positive-displacement ... lubrication system to provide a uniform oil film between closely fitting parts (e.g., piston rings and the cylinder wall). Partial or complete failure of the lube system results in...

Ngày tải lên: 05/08/2014, 11:20