Illustrated Sourcebook of Mechanical Components Part 7 potx
Illustrated Sourcebook of Mechanical Components Part 7 potx
... rev 7/ 32 = 5 .71 , (Ideal D/d ratio is between 4 and 8.) From charts Number of impacts per revolution for a D/d ratio of 5 .71 is 7. 8, Fig 2. Impacts are the number of balls ... fatigue life? From Eq 3 K = (1.53(1 07) (0.G 875 )0.5 = 1.269 X lo7 From Eq 1 2000 = (8)(1.269)(1 07) X 0.00001 97 = (6 - 0.0005)L.5J (7) From Eq 2 = 0.5(1...
Ngày tải lên: 11/08/2014, 08:22
Illustrated Sourcebook of Mechanical Components Part 2 potx
... Belts & Belting 3 -7 I 97. 8% Synchronous Belt Drive 100 1 90 80 70 60 Increasing DriveN Torque Synchronous belts are often used where precise positioning of components is required. ... 2.16 97 in. sprocket, cos 0 = O= - - O= cos 9 = - - 9= 1.66 67 in. r2 + C2 - R,2 2rC 0.5032 + 2.169P - 1 .71 46' 2 x 0.503 x 2.16 97 0.925 67...
Ngày tải lên: 11/08/2014, 08:22
Illustrated Sourcebook of Mechanical Components Part 10 potx
... without separaie machinery. 7 Barrel hopper . . . is most useful if parts tend to tangle. The parts drop free of the rotating- barrel sides. By chance selection some of them fall onto the vibrating ... seamwelded, brazed, or chemically milled as an integral part of the facing. A variation of this design, Fig. 7, shows attachment of a honevcomb sandwich rib to...
Ngày tải lên: 11/08/2014, 08:22
Illustrated Sourcebook of Mechanical Components Part 1 pptx
... 72 .8413 67 71.4666 73 .4666 73 .9081 68 72 .5333 74 .5333 74 . 975 2 69 73 .6000 75 .6000 76 .0422 70 71 72 73 74 75 76 77 78 79 74 .6666 75 .73 33 76 .8000 77 .8666 .78 .9333 80.0000 81.0666 ... 87. 4666 81moo 76 .6666 77 .1091 77 .73 33 78 . 176 1 78 .8000 79 .2432 79 .8666 80.3100 80.9333 81. 377 0 82.0000 82.4439 83.0666 83.51 07 84.1333 84....
Ngày tải lên: 11/08/2014, 08:22
Illustrated Sourcebook of Mechanical Components Part 3 docx
... more projecting pins, the 3um of the radii of the pins being equal to the eccentricity of offset of the shafts. The lines of criiter between each pair of pins remain parallel as the coupling ... the event of failure of one of the load-carrying members, the ball will spin within the socket and provide radial restraint. Containment for periods in excess of 25 h...
Ngày tải lên: 11/08/2014, 08:22
Illustrated Sourcebook of Mechanical Components Part 4 pptx
... other snaps. ILLUSTRATED SOURCEBOOK of MECHANICAL COMPONENTS SECTION 7 TUBING PIPE CONNECTIONS How to Connect Tubing-Cross and Tee Joints 7- 2 7- 4 7- 6 7- 7 7- 8 Different Mechanical ... and Eq (2), accurate values I of torque can be easily determined. ILLUSTRATED SOURCEBOOK of MECHANICAL COMPONENTS SECTION 9 Various Methods of Locking Threa...
Ngày tải lên: 11/08/2014, 08:22
Illustrated Sourcebook of Mechanical Components Part 5 pdf
... sides of sheet. FIG. 11-For attachment of recessed, solid metallic or non-metallic parts in thick-sectioned cylindrical parts. FIG. 12-For closing the end(s) of cylin- drical parts. ... Removal of the screw permits easy removal of the clampcd part. Heavy pressure toward the side of the key out of contact with the slot may permit slight movement due to the springin...
Ngày tải lên: 11/08/2014, 08:22
Illustrated Sourcebook of Mechanical Components Part 6 pps
... two- or three-parallcl designs Washers 11 -7 Tube crimped Gefol /lot wosher of end Rubber flof woshersv - VOCUl - Rubber Ball f /of wusher ‘Adhesive bond ‘Adhesive bond ‘Ploslic ... 1 to 52 1 to7 I 1/16 l/4 118 8 to 14 3132 15 to 27 1/8 28 to 52 I 3/16 I For Static Seals I For Dynamic Seals 0. 070 10.003 I 0.015 0.103 l0.003 0.0 17 0...
Ngày tải lên: 11/08/2014, 08:22
Illustrated Sourcebook of Mechanical Components Part 8 doc
... for Spring Pins 17- 8 Uses of Split Pins 17- 10 Design Around Spiral-Wrapped Pins 17- 12 A Penny-wise Connector - The Cotter Pin 17- 14 Alternates for Doweled Fasteners 17- 16 6 More Alternates ... space. ILLUSTRATED SOURCE BOOK of MECHANICAL COMPONENTS SECTION 18 CAMS Generating Cam Curves 18-2 Balance Grooved Cams 18-9 Computer and N/C Simplifies Cam Design 18-...
Ngày tải lên: 11/08/2014, 08:22
Illustrated Sourcebook of Mechanical Components Part 9 pps
... cutter-coordinate equations are not a simple varia- tion of the profile equations, because the normal fine at the point of tangency of the cutter and the profile does not continually pass through the cam ... certain curve, and if at each point of this curve at least one member of the family is tangent, the curve is either a part or the whole of the envelope of the...
Ngày tải lên: 11/08/2014, 08:22