Handbook of Small Electric Motors MAZ Part 12 doc

Handbook of Small Electric Motors MAZ Part 12 doc

Handbook of Small Electric Motors MAZ Part 12 doc

... in num- ber of turns. For example, an 8-pole design using 10 turn/coil of 22 AWG would have a K ET value of 0.97.A 2-pole design using 60 turn/coil of 22 AWG would have a K ET value of 0.88. The ... COMMUTATED MOTORS 5.35 From which the number of turns per slot require to produce E max is n s = int ΂΃ (5.42) where once again int (⋅) returns the integer part of its argument...

Ngày tải lên: 11/08/2014, 07:23

107 391 0
Handbook of Small Electric Motors MAZ Part 2 docx

Handbook of Small Electric Motors MAZ Part 2 docx

... mmf in dc series motors, 4.5–4.10, 4.117–4.119, 4 .122 –4 .126 and mmf in PMDC motors, 4.27–4.32 and mmf in universal ac motors, 4 .122 –4 .126 in permanent-magnet versus induc- tion motors, 3.25 permeance, ... E motors in PMDC motors, 4.45–4.46, 4.115 in polyphase motors, 6.100 in series dc and ac motors, 4 .128 –4.130 in single-phase motors, 6.56 in switched-reluctance motor...

Ngày tải lên: 11/08/2014, 07:23

28 325 0
Handbook of Small Electric Motors MAZ Part 3 docx

Handbook of Small Electric Motors MAZ Part 3 docx

... mold casting 12. 6 Plastic molding 12. 12 12. 15 extrusions 12. 19 machinery and molds 12. 17 parts design 12. 17 12. 28 Plastics 4.7 chemical resistance of 4.65 ... moments of 2.13 5.14 polar moments of 2.13 2.16 Inertia of masses, polar moments of 2.13 Institute of Electrical and Electronics Engineers (IEEE...

Ngày tải lên: 11/08/2014, 07:23

37 299 0
Handbook of Small Electric Motors MAZ Part 6 doc

Handbook of Small Electric Motors MAZ Part 6 doc

... more of the moving coil into the magnetic circuit. Also, ᏼ is constant, because the size of the air gap does not change as the position of the moving coil changes. Therefore, the rate of change of ... steel parts become saturated, the magnetizing force in the steel parts becomes large and the magnetizing force in the air gap becomes small (NI Ӷ NI coil ).The saturation of the st...

Ngày tải lên: 11/08/2014, 07:23

96 228 0
Handbook of Small Electric Motors MAZ Part 9 doc

Handbook of Small Electric Motors MAZ Part 9 doc

... improvements in flexibility, reliability, and speed. 3.11 BEARING SYSTEMS FOR SMALL ELECTRIC MOTORS* Electric motors are devices that convert electrical energy into magnetic energy and finally into mechanical ... designs. Producing finished stacks of rotor and stator laminations in the die has many advantages to the manufacturers of electric motors, particularly the eliminatio...

Ngày tải lên: 11/08/2014, 07:23

147 331 0
Handbook of Small Electric Motors MAZ Part 10 docx

Handbook of Small Electric Motors MAZ Part 10 docx

... constant Then: ω= − = 120 − 20 = 100 rad/s (4 .122 ) Or n = 100 = 955 rpm (4 .123 ) The stall torque can be found by setting ω=0. Then: T stall == = 6 N и m (4 .124 ) Efficiency of DC Motors Earlier discussion ... TR1, at the bottom of the slot, the angle is half of the tooth pitch angle: θ TR1 = (4.131) The length of the base of TR1 is L TR1 = (4.132) The angle within TR1 that t...

Ngày tải lên: 11/08/2014, 07:23

96 291 0
Handbook of Small Electric Motors MAZ Part 14 doc

Handbook of Small Electric Motors MAZ Part 14 doc

... way. Other PM synchronous motors are essentially PM stepper motors run as PSC motors. The motor shown in Fig. 7.19 has a stator consisting of two sets of coils with the teeth offset from each other ... length of air gap L met = mean end-turn length of coil L s = stator stack length l g = effective length of air gap L t1 = length of teeth L y1 = length of yoke MTL = mean tur...

Ngày tải lên: 11/08/2014, 07:23

24 257 0
Handbook of Small Electric Motors MAZ Part 1 pptx

Handbook of Small Electric Motors MAZ Part 1 pptx

... University. He has worked in sales of servo electric motors at Moog, Inc., and in sales of specialty motors at Doerr Electric. He is currently the vice president of Oven Systems, Inc. ANDREW E. ... associate professor in electrical engineering at the University of Maine. He holds PhD and MS degrees from the University of Illinois. He is a senior member of IEEE and an associ...

Ngày tải lên: 11/08/2014, 07:23

12 331 0
Handbook of Small Electric Motors MAZ Part 5 ppsx

Handbook of Small Electric Motors MAZ Part 5 ppsx

... Systems for Small Electric Motors / 3.46 3 .12. Sleeve Bearings / 3.72 3.13. Process Control in Commutator Fusing / 3.79 3.14. Armature and Rotor Balancing / 3.87 3.15. Brush Holders for Small Motors ... Electronically Commutated Motors 5.1 5.1. Brushless Direct-Current (BLDC) Motors / 5.1 5.2. Step Motors / 5.47 5.3. Switched-Reluctance Motors / 5.99 Chapter 6. Alternating-...

Ngày tải lên: 11/08/2014, 07:23

3 275 0
Handbook of Small Electric Motors MAZ Part 7 ppsx

Handbook of Small Electric Motors MAZ Part 7 ppsx

... press shop to have a set of dies for each steel supplier of a given part. This can raise the costs of keeping several steel suppli- ers for one part. Also,the subtleties of producing flat,round ... Hysteresis curves of magnetic material. where σ e = constant based on the quality of the iron, containing an element of resistivity of the material and the material density ∆=thic...

Ngày tải lên: 11/08/2014, 07:23

71 244 0
w