Volume 20 - Materials Selection and Design Part 10 pptx

... Corrosion-Resistant Materials Handbook, 4th ed., Noyes, 1985 • DECHEMA Corrosion Handbook: Corrosive Agents and Their Interaction with Materials, D. Behrens (Vol 1-9 ) and G. Kreysa and R. Eckermann ... Goldhoff and D.A. Woodford, The Evaluation of Creep Damage in a Cr-Mo-V Steel, STP 515, ASTM, 1972, p 8 9-1 06 86. R. Viswanathan and S.M. Gehl, Life-Assessment Techn...

Ngày tải lên: 10/08/2014, 13:20

... the design process and these design tools. Thus, Volume 20 of ASM Handbook is aimed at two important groups: materials professionals and design professionals. As a handbook on materials selection ... 9). If a part is necessary and a standard part can be used, then it is usually more economical to specify the standard part instead of designing and manufacturi...

Ngày tải lên: 10/08/2014, 13:20

... 4.43 2.21 -1 1.37 8 106 .16 102 .71 4.35 2.71 -1 3.08 9 96.33 102 .00 4.56 2.00 -8 .77 10 105 .94 102 .39 4.49 2.39 -1 0.28 11 97.91 101 .98 4.47 1.98 -1 0.65 12 98.41 101 .69 4.39 1.69 -1 2 .20 13 ... . 2 100 .81 99.40 1.41 -0 .60 -7 1.81 3 100 .47 99.75 1.26 -0 .25 -7 4.86 4 106 .08 101 .34 2.95 1.34 -4 1.05 5 111.21 103 .31 4.75...

Ngày tải lên: 10/08/2014, 13:20

... in CAE-based design optimization. Computer-aided-engineering- based design optimization does in fact turn CAE analysis tools into CAE design tools by replacing traditional trial -and- error design ... block-structured grids. On the other hand, unstructured-mesh CFD codes generally demand higher computational resources. Additional memory is needed to store cell-to-cell and vertex-...

Ngày tải lên: 10/08/2014, 13:20

... Selection, Granta Design, 1996 3. CMS Software and Handbooks, Granta Design, 1995 4. American Institute of Physics Handbook, 3rd ed., McGraw-Hill, 1972 5. Metals Handbook, 9th ed., and ASM Handbook, ... which follows in this Section of the Handbook) for materials selection in the minimum-weight design of ties, columns, beams, and plates, and for yield-limited design of...

Ngày tải lên: 10/08/2014, 13:20

... understanding of structure/property relationships resulted, and the design of materials evolves in partnership with design with materials. Structure and Structure Analysis. Materials science and ... J.J. Lewandowski, C.T. Liu, P.L. Martin, D.B. Miracle, and M.V. Nathal, Ed., The Metallurgical Society, 1993, p 1-1 5 9. M.F. Ashby, Materials Selection and Design,...

Ngày tải lên: 10/08/2014, 13:20

... ZA-8 Zn-8Al-1Cu-0.025 Mg 374 54 8 103 Z35630 ZA-12 Zn-11Al-1Cu-0.025Mg 404 58 5 100 Z35840 ZA-27 Zn-27Al-2Cu-0.015Mg 426 62 2 119 Wrought alloys (hot-rolled condition) Z21 220 . . . Zn-0.06Pb-0.06Cd ... Alloy 617 Ni-22Cr-3Fe-12Co-9Mo-1Al 755 110 350 51 58 173 HB Alloy 690 Ni-29Cr-9Fe 725 105 348 50 41 88 HRB Alloy 751 Ni-15Cr-7Fe-1Nb-2Ti 1 310 190 976 142 22 352 HB Nickel...

Ngày tải lên: 10/08/2014, 13:20

... 32 0- 426 6-8 8 3-1 03 1 2- 15 10 3- 138 1 5- 20 13. 8- 17.2 2. 0- 2.5 24 1- 276 3 5- 40 1. 5-2 .5 13 80 0- 106 5 15 -2 0 8 3-1 10 1 2- 16 13 8- 207 2 0- 30 17. 2- 20. 7 2. 5- 3.0 207 - 241 3 0- 35 ... <0.01 18 0-2 40 0 .20 40 PP 0.0 1-0 .03 200 -2 60 0.25 100 PMMA 0.1 0-0 .40 24 0-2 60...

Ngày tải lên: 10/08/2014, 13:20

... mold-cooling program allows designers and molders to evaluate materials and process parameters in a rapid, convenient, and cost-efficient manner. Plastic parts are usually thin, and thus a one-dimensional, ... 140 3-1 409 44. J.H. Selverian and S. Kang, Ceramic-to-Metal Joints: Part II-Performance and Strength Prediction, Am. Ceram. Soc. Bull., Vol 71 (No. 10) , 1992,...

Ngày tải lên: 10/08/2014, 13:20

... the initial design of the casting is the design of gates and risers. This consists of proper orientation of the part and the determination of the parting plane and the size, number, and location ... the time it takes an assembler to pick up and orient each part before the part is assembled. Jigs and trays, and so forth, that reduce this pick -and- place orientation...

Ngày tải lên: 10/08/2014, 13:20