Volume 20 - Materials Selection and Design Part 8 potx

... 2. 0- 2.5 24 1- 276 3 5- 40 1. 5-2 .5 13 80 0- 1065 15 -2 0 8 3-1 10 1 2- 16 13 8- 207 2 0- 30 17. 2- 20. 7 2. 5- 3.0 207 - 241 3 0- 35 1. 0-1 .5 25 1 96 0- 1335 1 8- 2 5 10 3- 1 38 1 5- 20 17 2- 241 ... (2 3-2 50 °C), 10 -4 in./in./°C <6 < 3 0-6 5 0. 6-1 .2 5 5 -8 3 8- 1 2 6 9-1 03 1 0...

Ngày tải lên: 10/08/2014, 13:20

... the design process and these design tools. Thus, Volume 20 of ASM Handbook is aimed at two important groups: materials professionals and design professionals. As a handbook on materials selection ... 9). If a part is necessary and a standard part can be used, then it is usually more economical to specify the standard part instead of designing and manufacturi...

Ngày tải lên: 10/08/2014, 13:20

... 80 0 Ni-21Cr-39.5Fe-0.4Ti-0.4Al 600 87 295 43 44 1 38 HB Alloy 617 Ni-22Cr-3Fe-12Co-9Mo-1Al 755 110 350 51 58 173 HB Alloy 690 Ni-29Cr-9Fe 725 105 3 48 50 41 88 HRB Alloy 751 Ni-15Cr-7Fe-1Nb-2Ti ... ZA -8 Zn-8Al-1Cu-0.025 Mg 374 54 8 103 Z35630 ZA-12 Zn-11Al-1Cu-0.025Mg 404 58 5 100 Z3 584 0 ZA-27 Zn-27Al-2Cu-0.015Mg 426 62 2 119 Wrought alloys (hot-rolled condition) Z...

Ngày tải lên: 10/08/2014, 13:20

... Density Constants for Volume and Surface-Flaw-Induced Fracture in Ceramics," TM- 10 089 0, National Aeronautics and Space Administration, 1 988 37. J.P. Gyekenyesi and N.N. Nemeth, Surface ... mold-cooling program allows designers and molders to evaluate materials and process parameters in a rapid, convenient, and cost-efficient manner. Plastic parts are usually thin...

Ngày tải lên: 10/08/2014, 13:20

... strength, MPa A 2 5-7 25 No 0.0105 -0 .0007 -0 .00 98 Phase 1 -1 00 100 B 725 Yes -0 .0025 0.0017 0.00 08 Phase 2 100 100 C 72 5 -8 50 No 0.0026 -0 .0017 -0 .0009 Phase 2 -5 0 50 D 85 0-3 00 No -0 .0116 0.0017 ... electrode and flux deposited per hour 7.1 kg (15.6 lb) Weight of electrode and flux deposited per foot of weld: Original design (...

Ngày tải lên: 10/08/2014, 13:20

... 9. 98 9.60 9.36 9 .20 9.07 8. 98 8.90 8. 84 8. 75 8. 66 8. 56 8. 51 8. 46 8. 41 8. 36 8. 31 8. 26 5 10.01 8. 43 7.76 7.39 7.15 6. 98 6 .85 6.76 6. 68 6.62 6.52 6.43 6.33 6. 28 6.23 6. 18 6.12 6.07 6.02 6 8. 81 ... -0 .64 25 101.99 100 .80 4 .87 0 .80 -2 .52 26 103.34 100.90 4 .80 0.90 -3 .92 27 102.49 100.96 4.72 0.96 -5 .52 28 96.60 100 .80 4.7...

Ngày tải lên: 10/08/2014, 13:20

... "Electronic Design Interchange Format," EDIF 200 (EIA 54 8- 1 988 ), EDIF 300 (EIA 61 8- 1994), and EDIF 400 (EIA 68 2-1 996), Electronic Industries Association, Arlington, VA Design Optimization ... 1030 3-1 1: 1994, ISO 1030 3- 11:1994, International Organization for Standardization 9. "Electronic Design Interchange Format," EDIF 200 (EIA 54 8...

Ngày tải lên: 10/08/2014, 13:20

... No. N-00014092-J- 180 8 are gratefully acknowledged. References 1. Metals Handbook, Vol 1, 8th ed., American Society for Metals, 1961, p 18 5-1 87 2. G. Dieter, Engineering Design, A Materials ... Selection, Granta Design, 1996 3. CMS Software and Handbooks, Granta Design, 1995 4. American Institute of Physics Handbook, 3rd ed., McGraw-Hill, 1972 5. Metals Handbook, 9...

Ngày tải lên: 10/08/2014, 13:20

... to Overstress, Eng. News-Rec., Vol 94 (No. 5), 29 Jan 1925, p 18 8- 1 89 19. Welded Bridge Failure in Belgium, Eng. News-Rec., Vol 120 (No. 18) , 5 May 19 38, p 65 4-6 55 20. O. Bondy, Brittle ... Westbrook, Materials: History Before 180 0, Encyclopedia of Materials Science and Engineering, M.B. Bever, Ed., Pergamon Press, 1 986 , p 281 6-2 82 7 7. J.H. Westbrook, M...

Ngày tải lên: 10/08/2014, 13:20

... 19 48, p 75 15. C. Herring, J. Appl. Phys., Vol 21, 1950, p 43 7-4 45 16. R.L. Coble, J. Appl. Phys., Vol 34, 1963, p 167 9-1 684 17. M.F. Ashby, Acta Metall., Vol 20, 1572, p 88 7 -8 97 18. ... Corrosion-Resistant Materials Handbook, 4th ed., Noyes, 1 985 • DECHEMA Corrosion Handbook: Corrosive Agents and Their Interaction with Materials, D. Behrens (Vol 1-9 )...

Ngày tải lên: 10/08/2014, 13:20