Volume 18 - Friction, Lubrication, and Wear Technology Part 7 pps

... 28 3-2 99 16. G. Levy and J. Morri, Impact Fretting Wear in CO Based Environments, Wear, Vol 106, 1985, p 9 7- 1 38 17. I.R. Sare, Repeated Impact-Abrasion of Ore-Crushing Hammers, Wear, Vol 87, ... p 20 7- 2 25 18. R.G. Bayer, Impact Wear of Elastomers, Wear, Vol 112, 1986, p 10 5-1 20 19. P.A. Engel and D.L. Millis, Surface Topography Study in Impact Wear,...

Ngày tải lên: 10/08/2014, 13:20

... plate FOF 0.09 0.08 18 Cu FOF 0.13 0.11 18 Ni (0.001 P) FOF 0.15 0.12 18 Steel, 1032 FOF 0. 27 0. 27 18 Ti-6Al-4V FOF 0. 17 0.14 18 Teflon TiN (Magnagold) FOF 0.15 0.12 18 UHMWPE Steel, mild ... Vol 179 G, 1 976 55. N. Bay, T. Wanheim, and B. Avitzur, Modeling of Friction in Metal Forming, Proceedings of NAMRC 15 (Bethlehem, PA), 2 7- 2 9 May 19 87, p 37 2-3...

Ngày tải lên: 10/08/2014, 13:20

... Trans. A, Vol 7A, 1 976 , p 1099 57. J.M. Martin, J.L. Mansot, I. Berbezier, and M. Belin, Microstructural Aspects of Lubricated Mi ld Wear With Zinc Dialkyl-dithiophosphate, Wear, Vol 1 07, 1986, ... Heinrich, Electron Beam X-Ray Microanalysis, Van Nostrand Reinhold, 1981 48. L.K. Ives, Abrasive Wear by Coal-Fueled Engine Particles, Proceedings Corrosion Erosion- Wear of M...

Ngày tải lên: 10/08/2014, 13:20

... 0.04 70 .7 0.05 74 .1 0.06 76 .9 0. 07 79 .2 0.08 81.2 0.09 82.8 0.10 84.2 0.11 85.4 0.12 86.4 0.13 87. 1 0.14 87. 7 0.15 88.2 0.16 88.5 0. 17 88 .7 ... tribosystem, three different wear stages can be distinguished: • Self-accommodation or running-in wear • Steady-state wear • Self-acceleration (catastrophic damage) of w...

Ngày tải lên: 10/08/2014, 13:20

... . . . 5 0-6 0 Cast tubes 7 0-1 40 1 0-2 0 12 5-2 20 1 8- 32 4 5-6 5 Wrought plate 8 0-1 40 1 2-2 0 14 0-1 70 2 0-2 5 4 0-5 5 Low-tin alloys Steel backed . . . . . . . . . . . . 3 5-4 5 Tin-free alloys ... condition, Alloy 188 and Alloy C- 276 were tested in both the solution annealed and 30% cold-worked conditions, and Alloy 71 8 was test...

Ngày tải lên: 10/08/2014, 13:20

... Vol 65, 1 970 , p 23 4-2 37 15. J.C. Gregory, Tribology Int., Vol 3, 1 970 , p 7 3-8 3 16. K H. Habig, R. Chatterjee-Fischer, and F. Hoffmann, Härt Tech. Mitt., Vol 33, 1 978 , p 2 8-3 5 17. K H. ... Mitt., Vol 31, 1 976 , p 13 7- 1 44 25. Fr.W. Eysell, Durferr. Hausmitt., Vol 28, 1958, p 7 -1 8 26. H. Tauscher and E. Stecher, IfL-Mitt., Vol 4, 1965, p 22 0...

Ngày tải lên: 10/08/2014, 13:20

... 192 3-1 933)) • N.E. Promisel (195 5-1 961) (Member, 195 4-1 963) • G.J. Shubat (1 97 3-1 975 ) (Member, 196 6-1 975 ) • W.A. Stadtler (196 9-1 972 ) (Member, 196 2-1 972 ) • R. Ward (1 97 6-1 978 ) (Member, 1 97 2-1 978 ) ... (Member, 195 5-1 958, 196 0-1 964) • G.V. Luerssen (194 3-1 9 47) (Member, 194 2-1 9 47) • G.N. Maniar (1 97 9-1 980) (Member, 1 9...

Ngày tải lên: 10/08/2014, 13:20

... materials and formaldehyde-release agents. Phenolic materials, such as 2,4,5-trichlorophenol, destroy bacteria directly. Materials such as 1,3-di(hydroxy-methyl )-5 , 5- dimethyl-2,4-dioxoimidazole, ... 1986, p 74 0 -7 50 • A.D. Cron and J. Fatkin, Graphite in Lubrication: Fundamental Parameters and Selection Guide, NLGI Spokesman, Vol 53 (No. 4), 1989, p 13 7- 1 47 • M. F...

Ngày tải lên: 10/08/2014, 13:20

... steel hardness Fig. 7 Surface composition of a worn 6 0-4 0 brass pin rubbed by an 18W-4Cr-1V-1C composition high- speed tool steel wheel particularly by McDowell, Tierney, and McClellan (Ref ... of Erosive- Corrosive Wear in Steam Extraction Piping, Paper 8 7- JPGC-Pwr-35, American Society of Mechanical Engineers, 19 87 30. P.A. Coulon, Erosion-Corrosion in Steam Turbines...

Ngày tải lên: 10/08/2014, 13:20

... motor-current signatures, as shown in Fig. 7. Fig. 7 Open-to-close stroke actuations of a 75 mm (3 in.) motor- operated valve before and after lubricating the worm and worm gear. (a) As- found ... D.P. Anderson and R.D. Driver, Equilibrium Particle Concentration in Engine Oil, Wear, Vol 56, 1 979 , p 41 5-4 19 38. W.W. Seifert and V.C. Westcott, A Method for the Stud...

Ngày tải lên: 10/08/2014, 13:20