The Science and Technology of Materials in Automotive Engines Part 8 pptx
The Science and Technology of Materials in Automotive Engines Part 8 pptx
... engine, two-stroke engine Science and technology of materials in automotive engines1 84 Gas carburizing Gas carburizing is carried out in a gaseous atmosphere containing CO and CH 4 . The gas dissociates ... stress, and the applied strain makes steel hard (known as work hardening, see Fig. 8. 7). Deformation increases the dislocation density in the Science...
Ngày tải lên: 10/08/2014, 12:21
The Science and Technology of Materials in Automotive Engines Part 11 pptx
... shell is broken off by vibration or high- pressure water blasting (f). Next, the gates and runners are cut off, and sand blasting and machining finish the casting. Investment castings often do not ... engines2 50 blades, and exits at the center of the housing. The expanded engine exhaust gas is directed through the exhaust manifold into the turbine housing. The exha...
Ngày tải lên: 10/08/2014, 12:21
The Science and Technology of Materials in Automotive Engines Part 1 doc
... Nitriding 187 8. 5.3 Nitrocarburizing 188 8. 5.4 Carbonitriding 189 8. 5.5 Ion nitriding 190 8. 5.6 Induction hardening 191 8. 6 Micro-alloyed steel 194 8. 7 Strengthening 1 98 8 .8 Conclusions 204 8. 9 ... and technology of materials in automotive engines Science and technology of materials in automotive engines8 2. The multi-cylinder engine has becom...
Ngày tải lên: 10/08/2014, 12:21
The Science and Technology of Materials in Automotive Engines Part 3 doc
... piston appeared at the beginning of the 20th century just after the invention of the electrolytic smelting technology of aluminum in 188 6. At that time, internal combustion engines used cast iron ... is fiber-reinforced. The top ring groove is reinforced with a Niresist ring carrier. Science and technology of materials in automotive engines5 4 and then,...
Ngày tải lên: 10/08/2014, 12:21
The Science and Technology of Materials in Automotive Engines Part 5 potx
... a ring installed in the ring groove. The piston with rings is inserted into the cylinder bore. The ring then expands from its initial diameter (d 1 ) and is forced tightly against the cylinder ... the outer surface of the stacked rings. The shaft revolves and moves up and down with the rings. During this motion, the rings are slightly inclined in the cylindri...
Ngày tải lên: 10/08/2014, 12:21
The Science and Technology of Materials in Automotive Engines Part 6 pps
... alloys Machining Final inspection Deburring Grinder Gate cutting Shot blasting Parting Pouring Sand recycling Sand mold Molding Electric furnace melting Inoculation Ladle Cam lobe Chiller Science and technology ... the value, the more severe the working conditions. 7. Withstand load Science and technology of materials in automotive engines1 34 Figure 6.4 summarizes...
Ngày tải lên: 10/08/2014, 12:21
The Science and Technology of Materials in Automotive Engines Part 7 pps
... are sintered first. It contains pores among the particles. The Cu is infiltrated into the pores. 100 µm Science and technology of materials in automotive engines1 62 In trucks and large industrial ... additives are ground and mixed Molding with press Giving enough strength for the following machining Rough machining to reduce the grinding allowance Firing Finish...
Ngày tải lên: 10/08/2014, 12:21
The Science and Technology of Materials in Automotive Engines Part 9 pdf
... small amount of carbon is added simultaneously. For carburizing and nitriding, the Science and technology of materials in automotive engines2 10 raceway of the big end and the inner raceway of the crankpin. ... bearing for the big end. The needle rollers held in the retainer are inserted into the big end and run on the outer 9.3 Section shape....
Ngày tải lên: 10/08/2014, 12:21
The Science and Technology of Materials in Automotive Engines Part 10 ppsx
... present. Science and technology of materials in automotive engines2 24 Bearing metals contain soft metals such as tin or lead. These soft metals can deform to the shape of the adjacent part (the crankpin ... failure 97.5 90 50 10 5 10 6 10 7 10 8 Life (repetition number) Vacuum melting ESR Vacuum degassing Melted in the air 9.12 Effect of refining on the lif...
Ngày tải lên: 10/08/2014, 12:21
The Science and Technology of Materials in Automotive Engines Part 12 doc
... iron Assembling B.1 Camshaft for high rotational speeds. Science and technology of materials in automotive engines2 72 increases with increasing carbon content. The amount of ferrite inversely decreases. Coarse ... can be obtained by changing the heating temperature and the cooling speed after heating. The table lists the names of heat treatments, purposes, res...
Ngày tải lên: 10/08/2014, 12:21