The Science and Technology of Materials in Automotive Engines Part 6 pps
The Science and Technology of Materials in Automotive Engines Part 6 pps
... cutting Shot blasting Parting Pouring Sand recycling Sand mold Molding Electric furnace melting Inoculation Ladle Cam lobe Chiller Science and technology of materials in automotive engines1 24 in the melt ... conditions. The higher the value, the more severe the working conditions. 7. Withstand load Science and technology of materials in automotive en...
Ngày tải lên: 10/08/2014, 12:21
The Science and Technology of Materials in Automotive Engines Part 7 pps
... µm Science and technology of materials in automotive engines1 62 In trucks and large industrial engines, individual cylinder heads are often used on each cylinder for better sealing force distribution and ... additives are ground and mixed Molding with press Giving enough strength for the following machining Rough machining to reduce the grinding allowance Firing...
Ngày tải lên: 10/08/2014, 12:21
The Science and Technology of Materials in Automotive Engines Part 10 ppsx
... number) Vacuum melting ESR Vacuum degassing Melted in the air 9.12 Effect of refining on the life of bearing steel. Science and technology of materials in automotive engines2 36 10.7 Manufacturing process of catalyst. ... shell Science and technology of materials in automotive engines2 22 9.5 The plain bearing In the assembled con-rod, a plai...
Ngày tải lên: 10/08/2014, 12:21
The Science and Technology of Materials in Automotive Engines Part 1 doc
... manual if necessary. i The science and technology of materials in automotive engines Science and technology of materials in automotive engines8 2. The multi-cylinder engine has become more widespread. ... 152 Contents vii Science and technology of materials in automotive engines4 fuel injection. In a petrol engine the fuel is normally in...
Ngày tải lên: 10/08/2014, 12:21
The Science and Technology of Materials in Automotive Engines Part 3 doc
... is fiber-reinforced. The top ring groove is reinforced with a Niresist ring carrier. Science and technology of materials in automotive engines5 4 and then, the connecting rod transmits the power ... piston appeared at the beginning of the 20th century just after the invention of the electrolytic smelting technology of aluminum in 18 86. At that time, i...
Ngày tải lên: 10/08/2014, 12:21
The Science and Technology of Materials in Automotive Engines Part 5 potx
... 4 .6 shows a ring installed in the ring groove. The piston with rings is inserted into the cylinder bore. The ring then expands from its initial diameter (d 1 ) and is forced tightly against the ... the outer surface of the stacked rings. The shaft revolves and moves up and down with the rings. During this motion, the rings are slightly inclined in the cylin...
Ngày tải lên: 10/08/2014, 12:21
The Science and Technology of Materials in Automotive Engines Part 8 pptx
... engine, two-stroke engine Science and technology of materials in automotive engines1 84 Gas carburizing Gas carburizing is carried out in a gaseous atmosphere containing CO and CH 4 . The gas dissociates ... stress, and the applied strain makes steel hard (known as work hardening, see Fig. 8.7). Deformation increases the dislocation density in the Science and...
Ngày tải lên: 10/08/2014, 12:21
The Science and Technology of Materials in Automotive Engines Part 9 pdf
... small amount of carbon is added simultaneously. For carburizing and nitriding, the Science and technology of materials in automotive engines2 10 raceway of the big end and the inner raceway of the crankpin. ... bearing for the big end. The needle rollers held in the retainer are inserted into the big end and run on the outer 9.3 Section shape....
Ngày tải lên: 10/08/2014, 12:21
The Science and Technology of Materials in Automotive Engines Part 11 pptx
... The turbocharger. Science and technology of materials in automotive engines2 46 the gasoline engine (Fig. 10.9). The main problem is how to generate an instantaneous rich state. The catalyst also ... shell is broken off by vibration or high- pressure water blasting (f). Next, the gates and runners are cut off, and sand blasting and machining finish the castin...
Ngày tải lên: 10/08/2014, 12:21
The Science and Technology of Materials in Automotive Engines Part 12 doc
... iron Assembling B.1 Camshaft for high rotational speeds. Science and technology of materials in automotive engines2 72 increases with increasing carbon content. The amount of ferrite inversely decreases. Coarse ... Shot peening is an alternative F. 4 Leaf-like martensite in the retained austenite (white portions) of quenched JIS-S45C. 50 µm Science and technolo...
Ngày tải lên: 10/08/2014, 12:21