Plastic Product Material and Process Selection Handbook Part 3 ppt
Plastic Product Material and Process Selection Handbook Part 3 ppt
... D3 ¢/t "0 8 e e-i, Pe ,-t D3 m " 13 8 I'D t/I I'D ¢'D "! "r" ~3 (::r" 0 0 70 Plastic Product Material and Process Selection Handbook ... fittings and 84 Plastic Product Material and Process Selection Handbook electrical properties remain relatively constant over a wide range of temperatures...
Ngày tải lên: 10/08/2014, 12:21
Plastic Product Material and Process Selection Handbook Part 8 pptx
... thickness thickness thickness 31 59 32 30 62 33 34 54 29 43 43 23 41 45 24 28 65 36 44 42 23 37 50 27 31 59 32 18 99 55 18 99 55 27 -31 59-68 32 -37 28 65 36 Figure 5.6 Blown film line ... wide range of diverse products. Widths may range from less than 6 in. (15 cm) to more than 33 ft 246 Plastic Product Material and Process Selection Handbook TabIe...
Ngày tải lên: 10/08/2014, 12:21
Plastic Product Material and Process Selection Handbook Part 10 pptx
... is developed frozen in and throughout the wall thiclmess. Orientation on molecular 33 2 Plastic Product Material and Process Selection Handbook thermoplastics. As the plastic exits the die it ... drilling and milling will produce channels, and it is not usually possible to follow the cavity contours so closely (Chapter 17). 31 4 Plastic Product Material and...
Ngày tải lên: 10/08/2014, 12:21
Plastic Product Material and Process Selection Handbook Part 14 ppt
... 6-~ I-?, ] 23 B7 4 O 6.2 1 73 4-5 93 53 30 1 .37 1 73 3 C, 9.0 23S 9,0 I8fi 107 N.y'| on E,~I2 30 1 .30 135 4.0 8 .3 1 93 7.6 138 117 F'c-~',~a~T'.~te l0 126 83 9,0 5 2 I ... 5- 13 6-9 Heat resistance con~uOtlS~ °F 3O0 -35 0 30 0 -35 0 30 0-450 220-250 2,~-250 33 0-500 33 0-500 260 -30 0 35 0-6OO 35 0-5OO 35 0 600 225-250 225-250 150-1...
Ngày tải lên: 10/08/2014, 12:21
Plastic Product Material and Process Selection Handbook Part 19 ppt
... thermoforming 30 8 -32 annealing 31 2 compressed air supply 31 1 cooling 31 0 double-ended 31 4 drum 31 3 equipment 32 0 films 31 0, 31 5 heaters 31 4 heating capabilities 31 2 heavy-gauge 30 9-10 high-pressure ... sheets 4 03 sandwich structures 36 5 Save American Manufacturing (SAM) 575 Scorim Process (SP) 222 scrapless forming 33 0-1 screw 157, 228 -30 b...
Ngày tải lên: 10/08/2014, 12:21
Plastic Product Material and Process Selection Handbook Part 1 ppsx
... of a screw plasticator and controls the relationship between output rate and pressure drop through a die system or into a mold. 18 Plastic Product Material and Process Selection Handbook 0 ... This book provides 14 Plastic Product Material and Process Selection Handbook ~.) ~.) v~ 'O c- E .E E ~3 C) -O ~.) O_ E O ~J ~J ~3 v~ ~J...
Ngày tải lên: 10/08/2014, 12:21
Plastic Product Material and Process Selection Handbook Part 4 pps
... 96 Plastic Product Material and Process Selection Handbook stabilized grade) replaced die-cast aluminum and competing plastics in this application because ... Low-high Molding temp., °F <70 -32 0 <70 -33 0 270 -32 0 270 -36 0 280 -36 0 33 0-660 Shrinkage, % 2 8 O. t 0.4 1-1.2 1-1 5 l-1.5 O. 1-0 .3 Tensile strength, i0 ~ 6-10 4- 13 6-9 7-9 4-5 5-27 PSI Elongatio...
Ngày tải lên: 10/08/2014, 12:21
Plastic Product Material and Process Selection Handbook Part 5 pps
... heating and/ or cooling. 148 Plastic Product Material and Process Selection Handbook disperse a standardized plastic/ color concentrate mix. The computer software collects data during a test run and ... melting of plastics follows different phases that effect performances. 487 1 56 Plastic Product Material and Process Selection Handbook Plasticator melti...
Ngày tải lên: 10/08/2014, 12:21
Plastic Product Material and Process Selection Handbook Part 6 pot
... trial and error method for molding optimization. 184 Plastic Product Material and Process Selection Handbook and to improve molded part quality and labor productivity. The Shotscopc process ... is excessive residence time for the plastic particularly the engineering materials. Any plastic that 174 Plastic Product Material and Process Selection Han...
Ngày tải lên: 10/08/2014, 12:21
Plastic Product Material and Process Selection Handbook Part 7 doc
... single most popular process for forming TPs. It pro- cesses over 36 wt% of all plastics consumed worldwide into products 220 Plastic Product Material and Process Selection Handbook using several ... melt. The gas can be applied within specific part sections. 222 Plastic Product Material and Process Selection Handbook used between the plasticator and...
Ngày tải lên: 10/08/2014, 12:21