Modeling and Simulation for Material Selection and Mechanical Design Part 8 pps
Modeling and Simulation for Material Selection and Mechanical Design Part 18 pptx
... 1.35 58 N m lbf in 8. 85 08 0.1130 Pressure=stress MPa KSI d 0.145037 6 .89 479 Nmm 2 KSI d 0.145037 6 .89 479 Temperature 8C 8F 8F ¼(1 .8 8C)þ 32 8C ¼(8FÀ32)=1 .8 a 1 m 1000 mm. b 1ft 12in. c 1 N 9 .81 Ã gf. d 1 ... Bickford, J.H. An introduction to the Design and Behaviour of Bolted Joints; Series Mechanical Engineering; Marcel Dekker, New York: 1 981 ; Vol 13. 8. Carvill, J....
Ngày tải lên: 10/08/2014, 12:21
Modeling and Simulation for Material Selection and Mechanical Design Part 1 ppsx
... viscoplastic and creep deformation as they relate to quenching, forging, and casting processes. Modeling and simulation of mechanical properties, in particular, material behavior during plastic deformation, ... Derek Smith 18. Chains for Power Transmission and Material Handling: Design and Appli- cations Handbook, American Chain Association 19. Corrosion and...
Ngày tải lên: 10/08/2014, 12:21
Modeling and Simulation for Material Selection and Mechanical Design Part 3 ppt
... Metallurgy of Thermomechanical Processing of Steels and Other Metals; ISIJ: 1 988 ; 799. 17. Nishizawa, T. Tetsu-to-Hagne 1 984 , 70, 1 984 . 18. Sellars, C.M.; Whiteman, J.A. Met. Sci. 1979, 14, 187 . 19. Sellars, ... these models should be widely used for off-line simulation of designing steel compositions and processing condition and on-line simulation for guaranteeing mech...
Ngày tải lên: 10/08/2014, 12:21
Modeling and Simulation for Material Selection and Mechanical Design Part 4 pot
... 0.24 0.4C–1.32Mn 20,2 98 14.241 0.22 0.4C–2.43Mn 19,406 13.713 0.24 0.4C–0.2Cr 20 ,84 8 15.366 0.21 0.4C–2.1Cr 15,3 48 10.076 0.24 0.4C–3.6Cr 10,992 5. 481 0.42 0.4C–6.7Cr 2,005 1.6 98 2.32 0.4C–0.37Si ... 2.32 0.4C–0.37Si 21,929 16.351 0.19 0.38C–1.75Si 23,764 15.234 0.22 0.4C–2.75Si 25,3 68 10.050 0.15 0.4C 21,429 16.72 0.24 1.4C 30,000 40 .88 1 0.07 1.2C–2.0Mo 26,343 29.7 68 0. 08 Co...
Ngày tải lên: 10/08/2014, 12:21
Modeling and Simulation for Material Selection and Mechanical Design Part 5 pdf
... stresses and micro-residual stresses [1,2]. The macro-type depends on the plastic deformation of solid materials due to rapid non-uniform cooling. And, the strain and deformation due to phase transformation ... AlN VC VN TiC TiN NbC NbN ZrC ZrN A 7,130 9,500 7, 985 8, 872 15,573 7,714 10,440 8, 464 13,9 68 B 1.463 6.72 3.09 4.04 3 .82 3.27 3 .87 4.96 3. 08 Copyright 2004 by Marcel De...
Ngày tải lên: 10/08/2014, 12:21
Modeling and Simulation for Material Selection and Mechanical Design Part 6 pot
... 85 0 8C and the model was cooled to 308C with oil. The heat transfer coefficients h during quenching were calculated as a function of temperature by the methods mentioned below and were used for ... elastic–viscoplastic solids and viscous fluids to apply simulation of the casting process was proposed and verified by experi- mental and numerical results. On the other hand, a pro...
Ngày tải lên: 10/08/2014, 12:21
Modeling and Simulation for Material Selection and Mechanical Design Part 7 pot
... 375– 381 . 24. Ju, D.Y.; Inoue, T. In Simulation of Solidification and Thermo -mechanical Behavior in Continuous Casting Process, Modeling and Simulation in Metallur- gical Engineering and Materials ... 1 985 , 1, 81 5 82 2. 12. Inoue, T.; Wang, Z.G. Coupling between stress, temperature and metallic structures during process involving phase transformations. Mater. Sci. Technol...
Ngày tải lên: 10/08/2014, 12:21
Modeling and Simulation for Material Selection and Mechanical Design Part 8 pps
... Reserved. C. Material Laws for Wide Ranges of Temperatures and Strain Rates Material laws that describe the flow behavior over very wide ranges of tem- peratures and strain rates are needed for the simulation ... deformed geometry is symmetrical about the midplane (Fig. 8) . An FE -simulation is carried out for a compression test with _ ee¼ 0.001 sec À1 considering stain har...
Ngày tải lên: 10/08/2014, 12:21
Modeling and Simulation for Material Selection and Mechanical Design Part 9 pptx
... between the applied stress s and the internal back stress s i , the particle deformation resistance s p , the material creep resistance s F and the degree of damage D. For long-time creep under ... time t à , thus t à ¼ nmm À 2 2 1=n 1 B 81 Þ Figure 38 Time to minimum creep rate of Alloy 80 0HT for different creep stresses and temperatures. (From Ref. 84 .) Copyright 2004 b...
Ngày tải lên: 10/08/2014, 12:21
Modeling and Simulation for Material Selection and Mechanical Design Part 10 potx
... determined in experiments and by the finite-element simulation. With these results, the main reason for crack initiation and growth seems to be the relatively high local strains, and not the local stress, ... 50,000 cracks were classified in the steel X6 CrNi 18- 11 and more than 60,000 cracks in the steel X8CrNiMoNb16-16 for different temperatures and stresses. Based on the r...
Ngày tải lên: 10/08/2014, 12:21