Modeling and Simulation for Material Selection and Mechanical Design Part 3 ppt
Modeling and Simulation for Material Selection and Mechanical Design Part 18 pptx
... in 0. 039 370 25.400 m a ft b 3. 2808 0 .30 48 Area mm 2 in 2 0.001550 645.16 m 2 ft 2 10.764 0.0929 03 Volume mm 3 in 3 0.000061024 1 638 7 m 3 ft 3 35 .31 5 0.02 831 6 Mass g lb 0.0022046 4 53. 59 Force ... International Organization for Standardization: ISO 2 73: Fasteners—clearance holes for bolts and screws. www.iso.ch 29. International Organization for Standardization:...
Ngày tải lên: 10/08/2014, 12:21
Modeling and Simulation for Material Selection and Mechanical Design Part 1 ppsx
... viscoplastic and creep deformation as they relate to quenching, forging, and casting processes. Modeling and simulation of mechanical properties, in particular, material behavior during plastic deformation, ... parameters k and n in Avrami equation [29 31 ], formulating new equations corresponding to transforma- tion kinetics obtained experimentally [32 ], and adopting the...
Ngày tải lên: 10/08/2014, 12:21
Modeling and Simulation for Material Selection and Mechanical Design Part 3 ppt
... Int. 1992, 32 , 297. 43. Enomoto, M.; Atkinson, C. Acta Metall. Mater. 19 93, 41, 32 37. 44. Enomoto, M. Tetsu-to-Hagane 1994, 80, 6 53. 45. A ˚ gren, J. ISIJ Int. 1992, 32 , 291. 46. Anderson, J ... these models should be widely used for off-line simulation of designing steel compositions and processing condition and on-line simulation for guaranteeing mechanical propertie...
Ngày tải lên: 10/08/2014, 12:21
Modeling and Simulation for Material Selection and Mechanical Design Part 4 pot
... 22,6 43 17.481 0.22 0 .37 C–5.6Ni 23, 599 18,575 0.24 0.4C–0 .32 Mn 21,196 15. 737 0.24 0.4C–1 .32 Mn 20,298 14.241 0.22 0.4C–2.43Mn 19,406 13. 7 13 0.24 0.4C–0.2Cr 20,848 15 .36 6 0.21 0.4C–2.1Cr 15 ,34 8 10.076 ... Fe–P and Fe–P–Mo Alloys Chemical composition, at.% CSPMo 0.01 0.002 0.017 0 0.01 0.0 03 0.10 0 0.01 0.002 0.15 0 0.01 0.0 03 0.0 93 3.1 0.01 0.002 0. 033 3. 1 0.01 0.002...
Ngày tải lên: 10/08/2014, 12:21
Modeling and Simulation for Material Selection and Mechanical Design Part 5 pdf
... compound Parameter AlN VC VN TiC TiN NbC NbN ZrC ZrN A 7, 130 9,500 7,985 8,872 15,5 73 7,714 10,440 8,464 13, 968 B 1.4 63 6.72 3. 09 4.04 3. 82 3. 27 3. 87 4.96 3. 08 Copyright 2004 by Marcel Dekker, Inc. All ... stresses and micro-residual stresses [1,2]. The macro-type depends on the plastic deformation of solid materials due to rapid non-uniform cooling. And, the strain and d...
Ngày tải lên: 10/08/2014, 12:21
Modeling and Simulation for Material Selection and Mechanical Design Part 6 pot
... elastic–viscoplastic solids and viscous fluids to apply simulation of the casting process was proposed and verified by experi- mental and numerical results. On the other hand, a proposal based on ... problem, Ju and Inoue [62] proposed a numerical simulation method by the Eulerian coordinate, and application to the continuous casting pro- cess of steel slab was performed. A. Res...
Ngày tải lên: 10/08/2014, 12:21
Modeling and Simulation for Material Selection and Mechanical Design Part 7 pot
... 37 5 38 1. 24. Ju, D.Y.; Inoue, T. In Simulation of Solidification and Thermo -mechanical Behavior in Continuous Casting Process, Modeling and Simulation in Metallur- gical Engineering and Materials ... T. Simulation of the thermo -mechanical behavior and residual stresses in the spray coating process. J. Mater. Process. Technol. 1999, 92– 93, 2 43 250. 30 . Ju, D.Y. Simu...
Ngày tải lên: 10/08/2014, 12:21
Modeling and Simulation for Material Selection and Mechanical Design Part 8 pps
... Reserved. C. Material Laws for Wide Ranges of Temperatures and Strain Rates Material laws that describe the flow behavior over very wide ranges of tem- peratures and strain rates are needed for the simulation ... velocity c T and s ¼ av n = ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi 1 Àðv=c T Þ 2 q . 3. Athermal Deformation Processes In the range of intermediate temperatures and low strain ra...
Ngày tải lên: 10/08/2014, 12:21
Modeling and Simulation for Material Selection and Mechanical Design Part 9 pptx
... between the applied stress s and the internal back stress s i , the particle deformation resistance s p , the material creep resistance s F and the degree of damage D. For long-time creep under ... or carbide particles embedded within the grains. The particles obstacle the dislocation motion and increase the resistance to deformation. The strength depends mainly on the size and th...
Ngày tải lên: 10/08/2014, 12:21
Modeling and Simulation for Material Selection and Mechanical Design Part 10 potx
... investigation of further materials and treatments (Fig. 60b). Based on the models of McClintock [128] and of Rice and Tracey, Gurson [112] deduced a yield function for materials with randomly distrib- uted ... equal to the mean stress s m ¼ðs 1 þ s 2 þ s 3 Þ =3, which leads to a visco-plastic deformation of the material and hence to an increase in void volume. For an arbitrary...
Ngày tải lên: 10/08/2014, 12:21