Foseco Ferrous Foundryman''''''''s Handbook Part 5 ppsx

... (N/mm 2 ) EN-GJMB-300-6 12 or 15 300 6 – 150 max EN-GJMB- 350 -10 12 or 15 350 10 200 150 max EN-GJMB- 450 -6 12 or 15 450 6 270 150 –200 EN-GJMB -50 0 -5 12 or 15 500 5 300 1 65 2 15 EN-GJMB -55 0-4 12 or 15 550 4 340 180–230 EN-GJMB-600-3 ... 59 22-1981 Blackheart B30-06 12 or 15 300 6 B32-12 12 or 15 320 12 190 150 max B 35- 10 12 or 15 350 10 200 Pearlitic P 45- 06 12 or 15...

Ngày tải lên: 10/08/2014, 11:22

... hardness grades of grey iron (EN 156 1:1997) Grade EN-GJL- HB 155 HB1 75 HB1 95 HB2 15 HB2 35 HB 255 HB30 min – 100 120 1 45 1 65 1 85 max 155 1 75 1 95 2 15 2 35 255 Note: Consult EN 156 1:1997 for details. Figure ... 1180 0 50 0 0.3 600 180 355 1.9 4 25 808 250 17.2 300 51 60 212 25. 3 212 53 64 180 16.7 212 354 0 150 19.2 150 2880 1 25 10.6 150 159 0 90 6 .5 106 689 6...

Ngày tải lên: 10/08/2014, 11:22

... Si7Mg 6 .5 7 .5 0 .55 0.2 0. 35 0.2–0. 65 – 0. 15 0. 15 0. 15 0. 05 0. 05 0. 25 0. 05 0. 15 LM 25 sand/chill EN AC-44100 EN AC-Al Si12(b) 10 .5 13 .5 0. 65 0. 15 0 .55 0.1 – 0.1 0. 15 0.1 – 0.2 0. 05 0. 15 LM6 sand/chill EN ... treatment Time(hrs) Temp(°C) Al–Si5Cu3 LM4-TE 6–16 50 5 52 0 Hot water 6–18 150 –170 Al-Si7 Mg LM 25- TE 8–12 155 –1 75 LM 25- TB7 4–12 52 5 54 5 H...

Ngày tải lên: 10/08/2014, 11:22

... After LM13 250 5 0.27 0.18 (Al–Si12Cu1Mg1) LM 25 250 6 0.40 0.13 (Al–Si7Mg0 .5) LM28 250 10 0.28 0.18 (Al–Si8Cu1 .5 Mg1Ni1) L99 220 7 0. 25 0.12 (Al–Si7 Mg0.3) L 155 90 15 0.24 0.12 (Al–Cu4Si1) 86 Foseco ... A B C 68 Foseco Non -Ferrous Foundryman’s Handbook Figure 5. 3 Dimensions of INSURAL ATL one piece ladle liners (Table 5. 3). Figure 5. 4 Temperature loss with INSURAL la...

Ngày tải lên: 10/08/2014, 11:22

... ✓✓✓ ✓ LB1 CuSn7Pb 15 C CC496K ✓✓ ✓ LB2 CuSn10Pb10–C CC495K ✓✓✓ ✓ LB3 G–CuSn10Pb5 LB4 CuSn5Pb9–C CC494K ✓✓✓ ✓ LB5 CuSn5Pb20–C CC497K ✓✓ ✓ G1 G–CuSn10Zn2 G2 G–CuSn8Zn4Pb G3 G–CuSn7Ni5Zn3 Copper–aluminium ... CuZn35Pb2Al–C CC 752 S ✓✓ DZR2 CuZn33Pb2Si–C CC 751 S ✓ CuZn37Pb2Ni1AlFe–C CC 753 S ✓ PCB1 G–CuZn40Pb DCB1 CuZn38Al–C CC767S ✓ DCB2 G–CuZn37Sn DCB3 CuZn39Pb1Al–C CC 754 S ✓✓✓✓ – CuZn39Pb1Al...

Ngày tải lên: 10/08/2014, 11:22

... inoculation required. 4 .5 31.0 155 0 10.0 1000 86 164 grey 13 .50 5. 0 32.0 no 153 0 8.0 600 129 grey 12 .5 5.0 33.0 no 155 0 4.0 750 243 grey 16.0 x 5. 0 36.0 no 1470 8.0 1 750 250 178 grey 17.80 x 5. 0 36.0 no 150 0 2.0 ... 42 22 54 14.8 12.6 59 50 53 330 3300 109 43 22 60 18.3 15. 6 7360 57 410 4100 1 35 43 22 66 22.1 18.8 8900 60 50 0 50 00 1 65 44 22 72 26 .5 22 .5 10 650...

Ngày tải lên: 10/08/2014, 11:22

... 2.2–2 .5 0.6 3 .5 3.6 2.2–2 .5 0. 35 3 .5 3.6 2.2–2.4 0. 25 3 .5 3.6 2.2–2.4 0. 15 25 50 3 .5 3.6 2.1–2.3 0.7 3 .5 3.6 2.1–2.4 0.4 3 .5 3.6 2.2–2.4 0.3 3 .5 3.6 2.2–2.4 0.20 50 –100 3.4–3 .5 1.9–2.1 0.8 3.4–3 .5 ... 65- 45- 12 70 -50 - 05 80 -55 -06 80-60-03 100-70-03 120-90-02 1993 Japan JIS FCD 350 -22 400-18 400- 15 450 -10 50 0-7 600-3 700-2 800-2 G 550 2 19 95 Inter- ISO 1083...

Ngày tải lên: 10/08/2014, 11:22

... 0. 25 0 .55 0. 65 Si 0.20 0.60 – 0.60 – 0.60 – 0. 75 – 0. 75 Mn 0 .50 1.00 0 .50 0.80 0.40 0.70 0.30 0.70 0 .50 1.00 P – 0. 05 – 0. 05 – 0. 05 – 0.04 – 0.06 S – 0. 05 – 0. 05 – 0. 05 – 0.04 – 0.06 Cr – 0. 25 ... 7.86 59 .5 13.2 100 482 12.19 57 .8 19.0 200 52 3 12.99 53 .2 26.3 400 59 5 13.91 45. 6 45. 8 600 741 14.68 36.8 73.4 800 960 14.79 28 .5 108.1 1000 13.49 27.6 116 ....

Ngày tải lên: 10/08/2014, 11:22

... kgf/cm 2 psi (lbf/in 2 ) 10 0.10 1 .5 50 0 .51 7.3 100 1.02 14 .5 200 2.04 29.0 300 3.06 43 .5 400 4.08 58 .0 50 0 5. 10 72 .5 600 6.12 87.0 700 7.14 101 .5 182 Foseco Ferrous Foundryman’s Handbook Phenolic-isocyanates ... preventing runout. 170 Foseco Ferrous Foundryman’s Handbook 800 8.16 116.0 900 9.18 130 .5 1000 10.20 1 45. 0 2000 20.39 290.1 3000 30 .59 4 35. 1 4000...

Ngày tải lên: 10/08/2014, 11:22

... CARSET 50 0 series of hardeners Gel times (minutes) at 20 ° C CARSET 50 0 CARSIL 54 0 CARSIL 51 3 CARSIL 100 series 2.2 ratio 2.4 ratio 2 .5 ratio 50 0 8 7 5 511 9 8 6 52 2 13 12 8 53 3 19 15 9 54 4 1 05 53 ... (%) (%) (%) at 20°C tonne Low ratio 2.0 15. 2 30.4 54 .4 1 .56 850 641 Medium ratio 2.40 12.7 30.8 56 .5 1 .50 310 668 High ratio 2. 85 11.2 31.9 56 .9 1.48 50 0 677...

Ngày tải lên: 10/08/2014, 11:22