SolidWorks 2010 bible phần 3 pdf

SolidWorks 2010 bible phần 3 pdf

SolidWorks 2010 bible phần 3 pdf

... after Extrude3. If Extrude3 is expanded so that you can see Sketch3 under it, then drop the rollback bar to after Sketch3. If a warning message appears, telling you that Sketch3 will be temporarily ... Pane. Figure 5. 23 shows interfaces for both methods. FIGURE 5. 23 Use the Appearance PropertyManager to change color and material Chapter 6: Getting More from Your Sketches 233 FIGURE...

Ngày tải lên: 09/08/2014, 12:21

118 353 0
SolidWorks 2010 bible phần 9 pdf

SolidWorks 2010 bible phần 9 pdf

... perfectly flush hem may not be as accurate as it seems. Chapter 29: Using SolidWorks Sheet Metal Tools 9 23 FIGURE 29 .33 A comparison between default features for Base Flange and Insert Bends If ... with Specialized Functionality 942 FIGURE 30 .1 SolidWorks 2010 has a new Direct Editing tab on the CommandManager. Additional direct edit tools exist in SolidWorks that should possib...

Ngày tải lên: 09/08/2014, 12:21

118 493 0
Tài liệu Cài đặt, cấu hình giải pháp xử lý email trên TMG 2010 Firewall – Phần 3 pdf

Tài liệu Cài đặt, cấu hình giải pháp xử lý email trên TMG 2010 Firewall – Phần 3 pdf

... trên TMG 2010 Firewall – Phần 3 Trong phần này chúng tôi sẽ giới thiệu những gì bạn có khi thực hiện cấu hình các tính năng chống spam (anti-spam) trên TMG 2010 firewall. Trong phần ... vào đó chúng ta cũng đã kích hoạt các thành phần Forefront Protection for Exchange và Exchange Edge để cho phép bảo vệ anti-spam và anti-virus. Trong phần ba này, chúng tôi sẽ gi...

Ngày tải lên: 21/01/2014, 02:21

23 481 3
SolidWorks 2010 bible phần 1 pptx

SolidWorks 2010 bible phần 1 pptx

... Equations 34 3 Creating equations 34 4 Naming dimensions 34 4 Building the equation 34 6 Using comments 34 8 Using driven dimensions 34 8 Using equation tricks 35 1 IIF 35 1 SWITCH 35 2 Using Link Values 35 3 Using ... Configurations 36 0 Finding configurations 36 0 Deleting configs 36 0 Sorting configs 36 1 Activating configurations 36 3 Creating configurations 36 4 A new con...

Ngày tải lên: 09/08/2014, 12:21

118 377 1
SolidWorks 2010 bible phần 2 pps

SolidWorks 2010 bible phần 2 pps

... shown in Figure 2 .39 . FIGURE 2 .39 The Copy Settings Wizard To use the Copy Settings Wizard, follow these steps: 1. Close SolidWorks. Part I: SolidWorks Basics 118 FIGURE 3. 33 The Fully Define ... simultaneously. Figure 3. 18 shows the initial, intermediate, and final states of the sketch being stretched. FIGURE 3. 18 Using the Stretch sketch tool Part I: SolidWorks Basics...

Ngày tải lên: 09/08/2014, 12:21

118 276 0
SolidWorks 2010 bible phần 4 docx

SolidWorks 2010 bible phần 4 docx

... into Your Parts 33 4 FIGURE 8.22 Cosmetic Pattern options in the RealView tab of the Task Manager Mirroring in 3D Because symmetry is an important aspect of modeling parts in SolidWorks, mirror ... selected. Mirroring in 3D sketches Chapter 31 deals with 3D sketches in more detail, but I discuss the mirror functionality here to connect it with the rest of the mirroring and patterning to...

Ngày tải lên: 09/08/2014, 12:21

118 249 0
SolidWorks 2010 bible phần 5 doc

SolidWorks 2010 bible phần 5 doc

... graphics window or the selection list box selects the item. Figure 13. 3 shows the Select Other cursor and dialog box. FIGURE 13. 3 The Select Other cursor and dialog box Although this selection ... subassemblies. Chapter 13: Getting More from Mates 4 73 Multiple Mate mode Multiple Mate mode enables you to select one face in order to mate multiple parts to it. Figure 13. 4 shows the inte...

Ngày tải lên: 09/08/2014, 12:21

118 265 0
SolidWorks 2010 bible phần 6 ppsx

SolidWorks 2010 bible phần 6 ppsx

... are in a Layout, SolidWorks puts you into a 3D sketch with the Front (XY) plane activated, so it displays a small grid. Cross-Reference 3D sketches are addressed in Chapter 31 . n For now, you ... 2009 and this testing was done on 2010 SP 0.0. Here are some of the limitations of Layout: l The 3D sketch used for Layout has all the limitations that come with 3D sketches. l Sketch rela...

Ngày tải lên: 09/08/2014, 12:21

118 259 0
SolidWorks 2010 bible phần 7 ppt

SolidWorks 2010 bible phần 7 ppt

... is covered in more detail in Chapter 31 . Multi-body modeling is covered in Chapter 26. FIGURE 21.22 The Relative View PropertyManager 3D Drawing View Mode 3D Drawing View Mode is not technically ... view. You can invoke the 3D Drawing View Mode from the 3D Drawing View toolbar button, which is on the View toolbar and can be accessed by choos- ing View ➪ Modify ➪ 3D Drawing View from the...

Ngày tải lên: 09/08/2014, 12:21

118 339 0
SolidWorks 2010 bible phần 8 docx

SolidWorks 2010 bible phần 8 docx

... Programs ➪ SolidWorks ➪ DWGeditor. If you need to integrate data from the imported document into a native SolidWorks drawing, you can open the DWG file from the normal Open dialog box in SolidWorks. Tip If ... inside a 3D document. The ANSI Y14.41 standard is pri- marily about this transition. SolidWorks is responding to this type of requirement by adding features that enable you to...

Ngày tải lên: 09/08/2014, 12:21

118 240 0
w