Learning AutoCAD 2010, Volume 2 phần 4 potx

... units, if your final plot scale is 1 :40 , set DIMSCALE to 40 . For imperial units, if your final plot scale is 1 /4& quot;=1', set DIMSCALE to 48 ( 12 / .25 = 48 ). DIMSCALE will multiply the dimension ... command. 2. Select an arc or circle (1). 3. Specify a center location override (2) . 4. Specify a dimension line location (3). 5. Specify the jog locatio...

Ngày tải lên: 09/08/2014, 11:20

... Blocks Behave 22 4 Creating Blocks 22 6 Inserting Blocks 23 2 Exercise: Create and Insert Blocks 23 8 Lesson: Working with DesignCenter 24 1 Using DesignCenter 24 2 Exercise: Use DesignCenter 24 5 Lesson: ... Fills 20 9 Challenge Exercise: Architectural 21 2 Challenge Exercise: Mechanical 21 4 Chapter Summary 21 7 Chapter 10: Working with Reusable Content 21 9 Lesson: Using...

Ngày tải lên: 09/08/2014, 11:20

... Introduction in Volume 1. 146 ■ Chapter 2: Creating Basic Drawings 4. For the next point: ■ Move the cursor down and to the right. ■ Enter 2& apos ;4 .25 . Press TAB. Enter 45 . Press TAB again. ■ ... Enter 2& apos ;4- 1 /4. Press TAB. ■ Enter 45 . Press TAB. ■ Click anywhere in the drawing to accept the point. 7. For the next point: ■ Move the cursor to the ri...

Ngày tải lên: 09/08/2014, 11:20

... able to: ■ Use the Properties palette to adjust object properties. 28 2 ■ Chapter 4: Drawing Organization and Inquiry Commands 2. On the Home tab, click Layers panel > Layer Control list. ... in your drawing that need to have their linetype changed. 3 04 ■ Chapter 4: Drawing Organization and Inquiry Commands 4. To match some of the properties from one wall hatch t...

Ngày tải lên: 09/08/2014, 11:20

... panels. Challenge Exercise: Mechanical ■ 39 2. Create a new layout configuration with the following settings: ■ DWF6 ePlot.pc3 ■ ISO A3 ( 42 0 x 29 7) ■ Three viewports that do not show on the ... left of 1 :2 ■ A scale factor for the view of the assembly on the right of 1 :4 3. Perform a cleanup: ■ Rename the layout Parts. ■ Delete Layout2. ■ Return to model spac...

Ngày tải lên: 09/08/2014, 11:20

... 0.9000 4. Add room labels and room ID numbers that are 300 mm tall as shown in the illustration: ■ 22 1 through 22 4 - SLEEPING QUARTERS ■ 20 1 - READY ROOM ■ 20 2 & 20 4 - LOCKER ROOM ■ 20 3 ... 20 3 - EXERCISE ROOM ■ 20 5 - DINING ROOM ■ 20 6 - KITCHEN ■ 20 7 - MEN'S TOILET ROOM ■ 20 8 - WOMEN'S TOILET ROOM 5. Save and close the drawing....

Ngày tải lên: 09/08/2014, 11:20

... 168 ■ Chapter 8: Dimensioning 2. Select a dimension (2) . Press ENTER. 3. Enter an oblique angle (i.e. 80). 1 42 ■ Chapter 8: Dimensioning New Dimension ... Add multileaders 4, 8, and 9 to the front pump housing. 12. To collect multileaders: ■ On the Leaders panel, click Collect. ■ Individually select multileaders 4, 8, and 9 in order....

Ngày tải lên: 09/08/2014, 11:20

... supported by AutoCAD LT. If you attempt this exercise in AutoCAD LT, you will need to use solid fills instead of gradient fills. The Hatch and Gradient dialog box is named the Hatch dialog box in AutoCAD ... different rooms. 4. Save and close the file. Imperial Units 1. Open the drawing you saved from the previous challenge exercise, or open I_ARCH-Challenge- CHP0...

Ngày tải lên: 09/08/2014, 11:20

... (1), set your scale factor (2) , and your rotation angle (3). The default rotation direction is CCW. 21 8 ■ Chapter 9: Hatching Objects Lesson: Using Blocks ■ 22 7 Block Definition ... has different linetype and color properties. Lesson: Using Blocks ■ 22 9 4. Under Objects, click Select Objects (4) . 5. Select the geometry to include in this block....

Ngày tải lên: 09/08/2014, 11:20

... Command line blank, select the spline. 2. Select a grip control point (1) and drag it to a new location (2) and click. 26 4 ■ Chapter 11: Creating Additional Drawing Objects Procedure: ... Ellipse Arc. 2. Click to specify the first axis endpoint (1) and the other axis endpoint (2) . 3. Click to specify the distance to the other axis endpoint (3)....

Ngày tải lên: 09/08/2014, 11:20