Learning AutoCAD 2010, Volume 1 phần 3 docx

... line. 10 . To draw a line perpendicular to the last: ■ Drag the cursor upward making sure that the angle field displays 90 degrees. ■ Enter 10 0. Press ENTER. 11 . To draw ... 11 6 ■ Chapter 2: Creating Basic Drawings 9. Repeat the previous step on the opposite side of the part. 10 . Close all files. Do not save. Lesson: Using Object Snaps...

Ngày tải lên: 09/08/2014, 11:20

... 9. Position the cursor so that the polar angle tooltip reads 15 .00 < 31 5 . Click the point. 16 6 ■ Chapter 3: Manipulating Objects Selecting with a Crossing Polygon To select ... with Units ■ 14 7 11 . For the next point: ■ Move the cursor to the left. ■ Enter 44'-5". Press TAB. ■ Enter 18 0. Press TAB. ■ Click anywhere in the drawing. 1...

Ngày tải lên: 09/08/2014, 11:20

... Drawing 31 6 Exercise: Use Linetypes 32 4 Lesson: Using Inquiry Commands 33 2 About Measuring 33 3 Using Measure Tools 33 4 Obtaining Object Information 34 4 Exercise: Obtain Geometric Information 34 7 Exercise: ... Snap Tracking 12 8 About Object Snap Tracking 12 9 Using Object Snap Tracking 13 0 Exercise: Use Object Snap Tracking 13 6 Lesson: Working with Units 13 9 About Units...

Ngày tải lên: 09/08/2014, 11:20

... ENTER. ■ Drag to < 90, and enter 1. 5 and press ENTER. ■ Drag to < 18 0, and enter 1 and press ENTER. ■ Drag to < 90, and enter 1 and press ENTER. ■ Drag to < 18 0, and enter 4 and press ENTER. ... point in the drawing window for the first point (1) . ■ Enter the polar coordinate @2<45 (2). Press ENTER. ■ Enter the polar coordinate @2< ; 13 5 (3) . Press ENTER....

Ngày tải lên: 09/08/2014, 11:20

... the basepoint. ■ Enter a rotation angle of 10 . Press ENTER. ■ Notice that the object is rotated 10 degrees counterclockwise. 18 4 ■ Chapter 3: Manipulating Objects 8. To position ... the cursor so that the polar angle displays 18 0 degrees. Click to select that point. 10 . Close all files. Do not save. 214 ■ Chapter 3: Manipulating Objects Lesson: Creat...

Ngày tải lên: 09/08/2014, 11:20

... Object's Size ■ 235 9. Select the center point of the larger circle. 10 . Enter 90. Press ENTER. 11 . Close all files. Do not save. 240 ■ Chapter 3: Manipulating ... Introduction in Volume 1. Lesson: Creating Object Patterns ■ 219 Procedure: Creating a Polar Array of Objects The following steps are an overview of creating polar arrays....

Ngày tải lên: 09/08/2014, 11:20

... in the Layers panel. 1. Select one or more objects in your drawing that need to be moved to a different layer. Lesson: Matching Object Properties ■ 30 3 3. To match some of ... ESC to clear the selected line. 10 . Select a dimension in the drawing. The Quick Properties panel automatically displays two property rows. 11 . On the status bar, right-cl...

Ngày tải lên: 09/08/2014, 11:20

... 3 = 10 3. 9447 mm Distance between circles 2 and 4 = 10 5.6296 mm 11 . Angle = 13 1 degrees Delta Y = 44.9275 mm 13 . X = 2 53 . 13 53Y = 0.0000Z = 0.0000 14 . Net area = 24255 .39 40 mm ... Answer 3. Distance = 55 mm Angle = 212 degrees 4. Radius for circle 2 = 17 .25 mm Radius for circle 4 = 10 .00 mm 5. Object type = LWPOLYLINE A...

Ngày tải lên: 09/08/2014, 11:20

... 37 2 ■ Chapter 5: Altering Objects 10 . To remove the construction lines: ■ Start the Erase command. ■ Select the lines indicated in the following image. Press ENTER. 11 . ... 11 . Your completed drawing. 12 . Close all files. Do not save. Lesson: Creating Parallel and Offset Geometry ■ 38 3 10 . To complete the offset: ■ Select the ce...

Ngày tải lên: 09/08/2014, 11:20

... lengths at 1 for the same results. 3. To chamfer using the polyline option: ■ Draw another 8 x 6 rectangle (see #1) . ■ Begin the Chamfer command. ■ See that the current chamfer length is 1 and ... corners are chamfered. 432 ■ Chapter 5: Altering Objects 11 . To select a door to relocate within a wall: ■ Start the Stretch command. ■ Click near point (1) and then poin...

Ngày tải lên: 09/08/2014, 11:20