Learning AutoCAD 2010, Volume 1 phần 2 doc

Learning AutoCAD 2010, Volume 1 phần 2 doc

Learning AutoCAD 2010, Volume 1 phần 2 doc

... point in the drawing window for the first point (1) . ■ Enter the polar coordinate @2& lt;45 (2) . Press ENTER. ■ Enter the polar coordinate @2& lt ;13 5 (3). Press ENTER. ■ Enter c for the ... ENTER. ■ Drag to < 90, and enter 1. 5 and press ENTER. ■ Drag to < 18 0, and enter 1 and press ENTER. ■ Drag to < 90, and enter 1 and press ENTER. ■ Drag to < 18 0, and enter...

Ngày tải lên: 09/08/2014, 11:20

46 447 0
Learning AutoCAD 2010, Volume 1 phần 3 docx

Learning AutoCAD 2010, Volume 1 phần 3 docx

... 11 6 ■ Chapter 2: Creating Basic Drawings 9. Repeat the previous step on the opposite side of the part. 10 . Close all files. Do not save. Lesson: Using Object Snaps ■ 10 7 ... Press F2. ■ Observe that @ symbol was automatically added to the coordinate making it relative to the last point you selected. ■ Practice making the following rectangles: ■ 2 x 2 (enter...

Ngày tải lên: 09/08/2014, 11:20

46 316 0
Learning AutoCAD 2010, Volume 1 phần 4 docx

Learning AutoCAD 2010, Volume 1 phần 4 docx

... symbol is typed. Example 16 ' -2& quot; can be simply typed: 16 &apos ;2 ■ When using Architectural units, you may type 16 ' -2& quot; or the equivalent in inches: 19 4 ■ If you work primarily ... section in the Introduction in Volume 1. 14 6 ■ Chapter 2: Creating Basic Drawings 4. For the next point: ■ Move the cursor down and to the right. ■ Enter 2& apos;4 .25...

Ngày tải lên: 09/08/2014, 11:20

46 344 0
Learning AutoCAD 2010, Volume 1 phần 6 doc

Learning AutoCAD 2010, Volume 1 phần 6 doc

... Lesson: Creating Object Patterns ■ 2 21 Practice Exercise: Creating an Array of Objects In this practice exercise, you draw a 1 x 1 rectangle and create an array using the Polar ... Introduction in Volume 1. Lesson: Creating Object Patterns ■ 21 9 Procedure: Creating a Polar Array of Objects The following steps are an overview of creating polar arrays. 1. On...

Ngày tải lên: 09/08/2014, 11:20

46 334 0
Learning AutoCAD 2010, Volume 1 phần 1 ppt

Learning AutoCAD 2010, Volume 1 phần 1 ppt

... to your drawing. AutoCAD ® 2 010 Autodesk Official Training Guide Essentials Autodesk Certification Preparation 001B1-050000-CM10A April 20 09 Learning A utoCAD ® 2 010 , Volume 1 Using hands-on ... Menus 14 More AutoCAD- Specific Interface Tools 15 Lesson: Working with Files 22 Working with Files 22 Lesson: Displaying Objects 26 Display Tools 27 Pan 27 Zoom Re...

Ngày tải lên: 09/08/2014, 11:20

33 412 1
Learning AutoCAD 2010, Volume 1 phần 5 pptx

Learning AutoCAD 2010, Volume 1 phần 5 pptx

... determines what you enter for the new angle. For instance, if point (2) was selected before point (1) , the new angle would have been 18 0. 20 6 ■ Chapter 3: Manipulating Objects Mirroring Objects ... line blank, select the objects. ■ Right-click one of the grips (1) . Click Mirror (2) . ■ Right-click again. Click Copy (3). 18 2 ■ Chapter 3: Manipulating Objects Exercise:...

Ngày tải lên: 09/08/2014, 11:20

46 350 0
Learning AutoCAD 2010, Volume 1 phần 7 potx

Learning AutoCAD 2010, Volume 1 phần 7 potx

... able to: ■ Use the Properties palette to adjust object properties. 28 2 ■ Chapter 4: Drawing Organization and Inquiry Commands 2. On the Home tab, click Layers panel > Layer Control list. ... ESC to clear the selected line. 10 . Select a dimension in the drawing. The Quick Properties panel automatically displays two property rows. 11 . On the status bar, right-c...

Ngày tải lên: 09/08/2014, 11:20

46 343 0
Learning AutoCAD 2010, Volume 1 phần 8 pot

Learning AutoCAD 2010, Volume 1 phần 8 pot

... circles 2 and 3 = 10 3.9447 mm Distance between circles 2 and 4 = 10 5. 629 6 mm 11 . Angle = 13 1 degrees Delta Y = 44. 927 5 mm 13 . X = 25 3 .13 53Y = 0.0000Z = 0.0000 14 . Net area = 24 255.3940 mm ... Distance = 55 mm Angle = 21 2 degrees 4. Radius for circle 2 = 17 .25 mm Radius for circle 4 = 10 .00 mm 5. Object type = LWPOLYLINE...

Ngày tải lên: 09/08/2014, 11:20

46 299 0
Learning AutoCAD 2010, Volume 1 phần 9 pot

Learning AutoCAD 2010, Volume 1 phần 9 pot

... (1) . ■ Select the object to join (2) . ■ Press ENTER to complete the command. 5. To Join the arc segments and close them. Method 1: ■ Begin the Join command. ■ Select one arc (1) ... 3 72 ■ Chapter 5: Altering Objects 10 . To remove the construction lines: ■ Start the Erase command. ■ Select the lines indicated in the following image. Press ENTER. 11 ....

Ngày tải lên: 09/08/2014, 11:20

46 252 0
Learning AutoCAD 2010, Volume 1 phần 10 pot

Learning AutoCAD 2010, Volume 1 phần 10 pot

... chamfered. 4 32 ■ Chapter 5: Altering Objects 11 . To select a door to relocate within a wall: ■ Start the Stretch command. ■ Click near point (1) and then point (2) to define the crossing ... ■ 403 10 . To move this object to the Hidden2 layer: ■ On the Layers panel, click the Layers list. ■ Click the Hidden2 layer to move the selected object to this layer. 11...

Ngày tải lên: 09/08/2014, 11:20

46 312 0
w