Learning AutoCAD 2010, Volume 1 phần 1 ppt

... Preparation 001B1-050000-CM01A April 2009 Learning A utoCAD ® 2 010 , Volume 2 Using hands-on exercises, learn the features, commands, and techniques for creating, editing, and printing drawings with AutoCAD ® ... Dimension Style 14 5 Lesson: Using Multileaders 14 8 About Multileaders 14 9 About Multileader Styles 15 1 Using Multileaders 15 4 Exercise: Use Multileaders 15 8 Le...

Ngày tải lên: 09/08/2014, 11:20

... 11 . On the command line, enter Regen. 12 . To expand the Hatch dialog box: ■ On the Home tab, click Draw panel > Hatch. ■ Expand the Hatch and Gradient dialog box. 13 . ... fill. 18 . Repeat the Gradient command, this time using a green color on the lower area of the elevation. Tip: Use the True Color tab of the Select Color dialog box, and enter 10 9, 18...

Ngày tải lên: 09/08/2014, 11:20

... grips. 1. With the Command line blank, select the spline. 2. Select a grip control point (1) and drag it to a new location (2) and click. 264 ■ Chapter 11 : Creating ... onscreen list of chapters and exercises, click Chapter 11 : Creating Additional Drawing Objects. Click Exercise: Create and Modify Polylines. 1. Open M_Polylines.dwg. 2. In th...

Ngày tải lên: 09/08/2014, 11:20

... Configure Layout1 to plot with the following settings: ■ Orientation: Landscape ■ Scale :1: 1 ■ Printer/Plotter: DWF6 ePlot.pc3 ■ Paper size: ISO A1 (8 41 x 594 mm) paper 3. Rename Layout1 to Plan ... 10 . On the Style panel, select ViewLabel from the text style list. 11 . Enter the text as shown below. 12 . Double-click outside the Text Editor to clos...

Ngày tải lên: 09/08/2014, 11:20

... as a subnote and the numbers are reordered. 10 . Click Close Text Editor on the Close panel. 11 . Zoom to the extents of the drawing. 12 . Close all files without saving. 82 ... text such as Width Factor and Oblique Angle. A Width Factor of 1 is normal. Less than 1 would make the text narrow and greater than 1 would make the text wide. Applying Height to the...

Ngày tải lên: 09/08/2014, 11:20

... arc length dimension: 1. Start the Dimarc dimension command. 2. Select an arc (1) . 3. Click to position the arc length dimension (2). 11 4 ■ Chapter 8: Dimensioning ... illustration shows a variety of dimensions for curved objects. Lesson: Creating Dimensions ■ 11 1 14 0 ■ Chapter 8: Dimensioning New Dimension Style Dialog Box - Fit Tab...

Ngày tải lên: 09/08/2014, 11:20

... (1) . ■ Move the cursor above the pulley and click a location (2). ■ Notice the command line. An attribute has been assigned to this block. Enter 1 (3). Lesson: Editing Dimensions ■ 16 3 Lesson: ... Dimedit and Dimtedit commands. Lesson: Using Multileaders ■ 16 1 9. Place a multileader on the bearing as shown. Enter 5. 10 . To add a multileader to an existing m...

Ngày tải lên: 09/08/2014, 11:20

... refer to the "Settings for the Exercises" section in the Introduction in Volume 1. 220 ■ Chapter 10 : Working with Reusable Content Lesson: Using Blocks This lesson describes how ... and hatch, as shown. ■ Enter 12 for the text height in the Style panel of the Text editor shown in the ribbon. ■ Enter COUPLER. ■ Click Close Text Editor. 11 . Close all files....

Ngày tải lên: 09/08/2014, 11:20

... Architectural ■ 311 6. Create a table showing the following Room Schedule data: ■ NUMBER - NAME - AREA ■ 2 21 - SLEEPING QUARTERS - 236 SQ/FT ■ 2 01 - READY ROOM - 386 SQ/FT ■ 202 - LOCKER ROOM - 15 0 ... Freeze layer construction. Zoom to display your completed drawing. 15 . Close all files. Do not save. 314 ■ Chapter 11 : Creating Additional Drawing Objects Chapter Su...

Ngày tải lên: 09/08/2014, 11:20

... originally set to plot at 1: 1 on an A1 size sheet of paper. It will not fit on A4 paper at 1: 1. Therefore, you need to change the scale factor for this page setup. 10 . To access the ... that 1: 1 is selected from the Scale list. ■ Click OK. 16 . In the Page Setup Manager dialog box, double- click the A2-ePlot page setup to assign it to Layout1 and click Close....

Ngày tải lên: 09/08/2014, 11:20