Expert CAD Management The Complete Guide phần 2 ppt

... will say their management team doesn’t give them the power they need to do the job. But I would argue that it’s the CAD manager’s responsibility to gain the power required to do the job. Nobody ... perspective on the CAD manager’s role should be, but I’ve noticed that the following views are widely held by corporate management: • The CAD manager should enable CAD- r...

Ngày tải lên: 08/08/2014, 23:21

... 2. Computer-aided design Management. I. Title. TA174.G75 20 07 620 '.00 420 285—dc 22 200700 621 3 TRADEMARKS: Wiley, the Wiley logo, and the Sybex logo are trademarks or registered trademarks of ... knows the CAD manager’s world. When CAD industry veterans seek out CAD Management consultants, Robert Green is at the top of every list. —D OUG WIETBROCK, President, DC...

Ngày tải lên: 08/08/2014, 23:21

... with properly named layers in the first place. Other Company (or department) DWG version 20 05 based standard 2D CAD Work (MicroStation v8) 2D CAD Work (AutoCAD 20 07) Your Company (or one department) Communication ... utilize these standards out of the box. If so, that’s great. Industry CAD Standards U.S. National CAD Standard (www.nationalcadstandard.org) .The NCS is th...

Ngày tải lên: 08/08/2014, 23:21

... happening with CAD management if you don’t do it, who will? The biggest reason CAD management misperceptions exist is precisely because most CAD managers don’t report to their management in a ... salary or benefits, the only way to lower your cost profile is to make CAD management part of job-billable expenses. Rather than doing CAD management as an overhead activity, g...

Ngày tải lên: 08/08/2014, 23:21

... 1:44 PM Page 23 3 22 5 ■ STORING DATA WAN environment: In WAN environments, you run the CAD software on the local machine to take advantage of the speed it offers the user. However, CAD files can ... environment: The best place to run the CAD software because it offers the highest speed for the user. CAD files may be stored here as well because no other user needs to...

Ngày tải lên: 08/08/2014, 23:21

... resolution and brightness is the only way to go. By showing the user the exact sequence of steps in the exact CAD software they’ll be using, they’ll see what they should be doing rather than interpreting ... procedures. They’re typically motivated by the concept that they have a better way to do it or that they can’t be bothered with the standards or procedures you’re requesting...

Ngày tải lên: 08/08/2014, 23:21

... you, the lessee. During the span of the lease, how you use the car is up to you as long as you meet the financial terms at the end of the lease. The car company won’t tell you how to drive the ... PARADIGM The Faster/Cheaper Paradigm We’ve come a long way in the CAD world in just the last 20 years. If you think about it, we’ve come from zero-PC-based CAD to univer...

Ngày tải lên: 08/08/2014, 23:21

... estimate of 28 hours of labor at $40 per hour equals $1, 120 ; and 1 hour of training per CAD user at $20 per hour equals $20 0 for the entire department. The total labor outlay is therefore $1, 320 . 16531c07.qxd ... because of the lack of a software utility. The CAD manager at the company couldn’t get management to authorize the software utility, thus perpetuating the b...

Ngày tải lên: 08/08/2014, 23:21

... give the most bang for the buck in almost all CAD management environments; therefore, I’ll concentrate on them. I’ve also found that these skills tend to be some of the weakest areas for many CAD ... collection of resources on CAD management, software cus- tomization,and industry trends specifically for CAD managers. www.cadalyst.com/cadman This is a well-indexed summary of...

Ngày tải lên: 08/08/2014, 23:21

... buying, 21 6 system components, 20 9 21 2 collaboration tools, 21 0 21 1 database engine, 20 9 programming APIs for customization, 21 1 21 2 system administration tools, 21 1 user interface modules, 20 9 21 0 view/print/redline ... locations, 22 3 security for, 27 28 file size 2D vs. 3D, 118–119 of CAD files, 28 file storage, 163–165 for AEC-focused CAD systems, 23 6 for Auto...

Ngày tải lên: 08/08/2014, 23:21