PSIM User Manual phần 9 pps
PSIM User Manual phần 9 pps
... appear in
PSIM as shown below.
Subcircuit port assignments
Creating a Circuit
PSIM User Manual
6-1
Chapter 6: Circuit Schematic Design
PSIM s schematic program provides interactive and user- friendly ... Specification
5-2
PSIM User Manual
with the time step set by the user, and the smaller value of the two will be used in the sim-
ulation. If the selected time step is dif...
PSIM User Manual phần 1 pdf
... Amplifier 2-22
Chapter 1: General Information
1-6
PSIM User Manual
Introduction
PSIM User Manual
1-1
Chapter 1: General Information
1.1 Introduction
PSIM is a simulation package specifically designed ... of the PSIM User Manual) , or in a main circuit if this resistor is in a subcircuit
(see Section 5.3.4.1, Chapter 5 of the PSIM User Manual) .
The power-of-ten suf...
PSIM User Manual phần 2 potx
... printout in Inductor i
L11 (self) 1.e-3
L12 (mutual) 0.9e-3
L22 (self) 1.1e-3
MUT2
MUT3
MUT4
Chapter 2: Power Circuit Components
2-8
PSIM User Manual
The following examples illustrate the control ... windings
TF_IDEAL
Np
Ns
TF_IDEAL_1
Np
Ns
Lp
Ls
Lm
Ideal
Rp
Rs
Np:Ns
Secondary
Primary
Switches
PSIM User Manual
2-13
The gating pattern has 6 switching points (3 pulses). The corr...
PSIM User Manual phần 3 pot
... Power Circuit Components
2-22
PSIM User Manual
2.5 Other Elements
2.5.1 Operational Amplifier
An ideal operational amplifier (op. amp.) is modelled using the PSIM power circuit ele-
ments, as ...
⋅
=
T
em
E
a
i
a
E
b
i
b
E
c
i
c
⋅
+
⋅
+
⋅()ω
m
⁄
=
J
d
ω
m
dt
⋅
T
em
B
ω
m
T
load
–
⋅
–=
d
θ
r
dt
P
2
ω
m
⋅
=
Motor Drive Module
PSIM User Manual
2- 29
The model INDM_3SN is...
PSIM User Manual phần 4 ppt
... currents
Brushless DC Motor
Speed
T
em
Phase A current
Vgs
Vgfb/2
Motor Drive Module
PSIM User Manual
2- 49
Attributes:
If the numbers of teeth of the first gear and the second gear are n
1
...
+
sin 2
θ
r
()
sin 2
θ
r
2
π
3
–
sin
i
a
i
b
i
c
⋅⋅ ⋅
–
⋅
=
Motor Drive Module
PSIM User Manual
2- 39
All the parameters are referred to the stator side.
The equations...
PSIM User Manual phần 5 pot
... Components
3-2
PSIM User Manual
The initial values of the state variables x
n
to x
1
can be specified at the input in the element
TFCTN1.
Example:
The following is a second-order transfer function:
In PSIM, ... only)
I
RESETI
V
d
v
ctrl
v
o
Gs
()
sT=
Transfer Function Blocks
PSIM User Manual
3-5
3.1.5 Built-in Filter Blocks
Four second-order filters are provided as built-in...
PSIM User Manual phần 6 pot
... 0
0.3 0.44 0.11 0.22 0.33 0.44
0.4 0.55 0.55 0.22 0.33 0.44
C_BUFFER
Logic Components
PSIM User Manual
3- 19
Attributes:
Example:
In the single-phase thyristor circuit below, a THD block is used ... 1–
()⋅
+=
Hz
()
1
T
z 1–
z
⋅
=
yn
()
1
T
un
()
un 1–
()
–
()⋅
=
Digital Control Module
PSIM User Manual
3- 29
Attributes:
The following are the filter images and attribu...
PSIM User Manual phần 7 potx
... Module
PSIM User Manual
3- 39
schematic file. In this example, we assume that the netlist is located in the
directory “C: \PSIM6 .0”. The netlist file name and path will be
“C: \PSIM6 .0\pmsm _psim. cct”.
In ... and saved under the same directory as the
Power
Control
in PSIM
in SimuLink
File: pmsm_simulink.mdl
File: pmsm _psim. sch
Sources
PSIM User Manual
4-7
For VGNL_1/IG...
PSIM User Manual phần 8 pot
... 268.7586 271.2414 272.7578 3 49. 8133 360.
14
10.1 894 26 87.470 09 88 .97 936 91 .02065 92 .5 299 1 1 69. 8106 180.
190 .1 894 267.4701 268 .97 93 271.0207 272.5 299 3 49. 8106 360.
In this example, if the modulation ... Components
4-18
PSIM User Manual
14
7.821 098 72.27710 80.72750 99 .27251 107.72 29 172.17 89 180.
187.8211 252.2771 260.7275 2 79. 2725 287.72 29 352.17 89...
PSIM User Manual phần 10 potx
... Design
6-12
PSIM User Manual
Simulation Issues
PSIM User Manual
8 -9
Chapter 8: Error/Warning Messages and General
Simulation Issues
8.1 Simulation Issues
8.1.1 Time Step Selection
PSIM uses ... 0.153 897 E+01 0.100000E+01
0.6000000E-04 0.000000E+00 -0.14 192 0E-17 0.184671E+01 0.100000E+01
0.7000000E-04 0.000000E+00 -0.1 694 49E-17 0.215443E+01 0.100000E+01
0.8000000E-0...