Designing Capable and Reliable Products Episode 1 Part 5 potx

... work Figure 1. 19 The FMEA input into designing capable and reliable products Designing for quality 25 Preface Notation Abbreviations 1 Introduction to quality and reliability engineering 1. 1 Statement ... problem 1. 2 The costs of quality 1. 3 How and why products fail 1. 4 Risk as a basis for design 1. 5 Designing for quality 1. 6 Designing for reliabili...

Ngày tải lên: 05/03/2014, 15:21

... reliability Better understanding of the eects of variability 34 Introduction to quality and reliability engineering Designing Capable and Reliable Products (Dale, 19 94; Kehoe, 19 96; Maylor, 19 96). This ®gure ... (Kotz and Lovelace, 19 98; Vasseur et al., 19 92). Making the product robust to variation is the driving force behind designing capable and reliable pr...

Ngày tải lên: 05/03/2014, 16:20

... (Kotz and Lovelace, 19 98; Vasseur et al., 19 92). Making the product robust to variation is the driving force behind designing capable and reliable products, lessens the need for inspection and can ... probable cost of failure per million products produced would be £8400. Figure 1. 12 Global quality±cost model (BS 614 3, 19 90) The costs of quality 15 companies, and in...

Ngày tải lên: 27/06/2014, 17:20

... Rule #1 mandates a ∅ .50 2 boundary of perfect form at MMC (envelope) Figure 5- 21 Rule #1 specifies a boundary of perfect form at MMC Geometric Dimensioning and Tolerancing 5 - 15 Table 5 -1 Geometric ... section 5. 8 .5. Figure 5 - 15 Conformance to limits of size for a width-type feature Figure 5 -16 Size limit boundaries control circularity at each cross section 5- 24 C...

Ngày tải lên: 21/07/2014, 15:20

... METRIC Code Size Code Size A 8 .5 X 11 A4 210 X 297 B 11 X 17 A3 297 X 420 C 17 X 22 A2 420 X 59 4 D 22 X 34 A1 59 4 X 8 41 E 34 X 44 A0 8 41 X 11 89 4.6 Title Blocks The part of a drawing that has the ... section Figure 4 -14 Half section Drawing Interpretation 4- 21 Figure 4 - 15 Offset section Figure 4 -16 Broken-out section Geometric Dimensioning and Tolerancing 5- 3 • ASM...

Ngày tải lên: 21/07/2014, 15:20

... Mech. 18 , 4 05 413 . Mallock, A. (18 81 82) The action of cutting tools. Proc. Roy. Soc. Lond. 33, 12 7 13 9. Merchant, M. E. (19 45) Mechanics of the metal cutting process. J. Appl. Phys. 16 , 318 –324. Oxley, ... Proc. I Mech. E. Lond. 209Pt.J, 13 1 13 6. Weiner, J. H. (19 55 ) Shear plane temperature distribution in orthogonal cutting. Trans ASME 77, 13 31 13 41. Williams, J. A. (1...

Ngày tải lên: 21/07/2014, 17:20

... 2006 12 Subsidy per gallon of pure ethanol 1. 05 1. 25 1. 05 1. 25 1. 05 1. 30 1. 00 1. 25 Subsidy per GGE of fuel 1 1. 45 1. 75 1. 40 1. 70 1. 45 1. 75 1. 40 1. 70 Subsidy per MMBtu 12 .55 15 . 15 12 . 45 15 . 05 12 .70 15 .30 ... 12 .55 15 . 15 12 . 45 15 . 05 12 .70 15 .30 12 . 15 14 . 75 Subsidy per GJ 11 .90 14 . 35 11 .80 14 . 25 12 . 05 14 .50 11 .5...

Ngày tải lên: 06/08/2014, 04:20

... transfer. TDI Safety and Handling The following contains information as of December 19 97. The health and safety information is partial. For complete, up-to-date information, obtain and read the current ... TDI and acids should be avoided. Contact with bases, such as caustic soda and primary and secondary amines, might produce a violent C -58 Chemicals (Toxic), Handling 3. Sweep...

Ngày tải lên: 21/07/2014, 16:22

... links. © 20 01 by CRC Press LLC Table E.2 Spatial One-dof Five-Link Chains. © 20 01 by CRC Press LLC Table E.3 Spatial One-dof Six-Link Chains. Table E.4 Spatial One-dof Seven-Link Chains. © 20 01 by CRC

Ngày tải lên: 21/07/2014, 17:20

... between x 1 ¼ h 1 =a and x 2 ¼ h 2 =a. The final analytical expression for the load capacity in a plane-slider is as follows: W ¼ 6mULB 2 h 2 2 1 b  1  2 ln b  2ðb  1 b þ 1 ! ð4 -19 Þ where ... pressure wave along the x direction (between x ¼ h 1 =a and x ¼ h 2 =a): p ¼ 6mU a 3 ðh 1  axÞðax h 2 Þ ðh 1 þ h 2 Þx 2 ð4 -17 Þ At the boundaries h ¼ h 1 and h ¼ h 2 ,...

Ngày tải lên: 21/07/2014, 17:20