Cutting Tool back matter Part 4 pdf

... 44 0 ballistic cutting speeds 43 2 beilby layer 362 bell-mouthing 135 eect 94 beta-function 3 24 bird nest 82 bird nesting 193 black, or mixed ceramic 22 block 45 0 processing time 44 9 tool ... 2 64 attrition wear 77 autocollimation 45 3 axial force component 82 axial force (F) 41 , 101 B B-spline 502, 5 04 back- lash 155 eliminator 155 back- taper 520 back...

Ngày tải lên: 05/08/2014, 21:21

... new thread cutting tools. [Courtesy of Guhring] . Appendix  Appendix 7a. (continued) Tap trouble-shooting guide (I) – problems, causes and solutions, with reground thread cutting tools. [Courtesy ... solutions, with reground thread cutting tools. [Courtesy of Guhring] .  Appendix Appendix 9a. Roundness assessment techniques – for component prole traces of “departures from roun...

Ngày tải lên: 05/08/2014, 21:21

... [Courtesy of ISO: extract from ISO 3685:1977 (E)].  Appendix Appendix 1a. ISO code key – external toolholders. [Courtesy of Sandvik Coromant].  Appendix Appendix 1c. ISO code key – cartridges. ... [Courtesy of Sandvik Coromant].  Appendix Appendix 5. Reaming trouble-shooting. [Courtesy of Seco Tools].  Appendix Appendix 3. Trouble-shooting for turning operations (1). [Courtesy of...

Ngày tải lên: 05/08/2014, 21:21

... wear patterns on cutting inserts – with possible causes and remedies. [Courtesy of Sandvik Coromant] .  Appendix Appendix 13a. Nomograph for determination of both spin- dle and cutting speeds ... Kuwait Petroleum International Lubricants] . Appendix  Appendix 11. Typical wear patterns on cutting inserts – with possible causes and remedies. [Courtesy of Sandvik Coromant] . Append...

Ngày tải lên: 05/08/2014, 21:21

... 532 time 5 34 tool coating chemical vapour deposition (CVD) 14 physical vapour deposition (PVD) 17 tool crash 5 34 tool driing 3 34 tool force 39 toolholder design 46 5 size and type 45 tool identication ... dynamometry 49 3 toolholders/chucks 45 8 with non-orthogonal machine tools and robots 45 1 HSM dynamics acceleration and deceleration 44 5 servo-lag 44 6 H...

Ngày tải lên: 05/08/2014, 21:21

... Controller’s tool table. Typical of such tooling, are special-purpose form tools that may be consid- ered to full this classication, 2. Semi-qualied tools – these are tools where not all of the tool ... competitors tooling products, • Obsolete tooling should be ‘weeded-out’ – particu- larly with the introduction and addition to the tool le of newer high-technology tooling, • In...

Ngày tải lên: 05/08/2014, 21:20

... this  assistance is oen provided by the cutting uid manu - facturer’s laboratory service department. .. Monitoring, Maintenance and Testing of Cutting Fluid – in Use While in use the cutting uid is subject to various in- uences  ... common  working-con- centration  of  5%  (i.e.  5  parts  MWF  to  95  parts  water),  this  would simply equate to 40 0,000 tonnes of waste cutting u...

Ngày tải lên: 05/08/2014, 21:20

Ngày tải lên: 07/08/2012, 11:57

Ngày tải lên: 13/12/2013, 20:15