Machining and Monitoring Strategies Part 7 ppt
Machining and Monitoring Strategies Part 7 ppt
... drilling and multi-axis milling
operations. [Courtesy of Kistler Instru-
mente AG]
.
Machining and Monitoring Strategies
Figure 245. The complex machining of either a sculptured, or die and mould ...
machined prole. [Courtesy of Sandvik Coromant]
.
Machining and Monitoring Strategies
Figure 243. Technique of manufacture of the aerospace aluminium disks and t...
Machining and Monitoring Strategies Part 1 ppt
...
Salomon, circa 1920’s–30’s]
.
Machining and Monitoring Strategies
Figure 2 17. Typical ‘modular design’ and construction of machining centres, with ‘ballscrews’ and ‘tychoways’. [Courtesy of ... Corporation]
.
Machining and Monitoring Strategies
7 µm. However, if linear encoders are tted this mini-
mises any potential ‘ballscrew wind-up’ , although the
probl...
Machining and Monitoring Strategies Part 5 pptx
...
directional plane.
Machining and Monitoring Strategies
Figure 234. Dynamic dual-plane (i.e. radial and axial) cutter balancing. [Courtesy of Ingersoll].
Machining and Monitoring Strategies
in ...
Wyatt & Hope, 1998]
.
Machining and Monitoring Strategies
Figure 233. A graph to determine high-speed cutter unbalance ‘U’ (ANSI S2.19–1989).
Machining...
Machining and Monitoring Strategies Part 6 ppt
... of
machine tools such as machining centres, has been
utilised for some of years (i.e typically: NAS Stan-
dard 979 : 1969; ISO Standard: 1 079 1 -7: 19 97; Knapp,
19 97) , being developed just for ... 2003]
.
Machining and Monitoring Strategies
Figure 2 37. An ultra-high-speed turning operation undertaken on a vertical machining centre. [Source: Smith, Littlefair,
Wyatt &a...
Machining and Monitoring Strategies Part 8 pptx
... generated pristine forms which would
Machining and Monitoring Strategies
Figure 249. By utilising a sophisticated cutter and part simulation technique, any potential and very costly ma-
chining mistakes ... surfaces; it has enabled
the hard -part machining process to become well-es-
tablished and commonplace. Prior to machining parts
in the hardened state, the time-...
Machining and Monitoring Strategies Part 2 docx
... positioning.
[Source: Smith and Maxted, 1995]
.
Chapter
Figure 222. The CNC control problem of servo-lag and its aect on the associated HSM motional kinematics.
Machining and Monitoring Strategies
less ... cutting tool to rest and press against
machined surface and thus, generate minute ‘gouging-eects’
in the surface. (Source: Seames, 1990; Smith, 1993)
Machinin...
Machining and Monitoring Strategies Part 3 doc
... G.T.]
.
Machining and Monitoring Strategies
Figure 225. Variax/Hexapod oers a unique and rigid design solution, with many production benets. [Cour-
tesy of Giddings & Lewis]
.
Machining and ... allows the ‘Variax’ to move and
accelerate up to ve times faster than a conventional machine
tool.
Machining and Monitoring Strategies
Figure 226. Robotic high-...
Machining and Monitoring Strategies Part 4 docx
... 24 inches of length. is 7/ 24 system
incorporates several Standards: CAT and BT 40- and 50-taper
tooling.
Machining and Monitoring Strategies
e capacity for the workpiece, or even a chuck ... operations.
[Courtesy of Heartech Precision Inc. (HPI)]
.
Machining and Monitoring Strategies
quickly heats up the holder and in so doing, expands
the bore allowing t...
Machining and Monitoring Strategies Part 9 pot
... 253. Micro- and nano -machining of parts is a big challenge for both today and tomorrow.
Machining and Monitoring Strategies
cutting edge corners – where high stresses and tem-
peratures are ... dimensional sizes and scales, for:
• machining of accurate and presicion parts or
• equated to their respective measurement.
[Source: Smith, et al., 2002]
.
Machining and...
Machining and Monitoring Strategies Part 10 ppsx
... [Source:
Lamb & Gull, 1999]
.
Machining and Monitoring Strategies
Figure 255. Some typical micro-tooling: drills and boring tools.
Machining and Monitoring Strategies
sizes of 25 µm. ... factor with any micro -machining machine
tool like the one mentioned above, is its machining
environment and more specically, its ‘thermal condi-
tions’
70
. As the mi...