Modular Tooling and Tool Management Part 4 pdf
Modular Tooling and Tool Management Part 4 pdf
... competitors tooling products, • Obsolete tooling should be ‘weeded-out’ – particu- larly with the introduction and addition to the tool le of newer high-technology tooling, • Investigation of new tooling ... Chapter Figure 1 34. Automatic cutting tool setting and tool breakage detection, utilising an ‘on-machine’ non-contact laser. [Courtesy of Renishaw plc] . Modula...
Ngày tải lên: 05/08/2014, 21:20
Modular Tooling and Tool Management Part 1 ppsx
... Machines] . Modular Tooling and Tool Management 6.1 Modular Quick-Change Tooling Introduction e modular tooling concept was developed by cut- ting tool manufacturers from the long-standing tool- ing ... employing modular quick-change tooling on a turning centre, via the ‘intelligent/ tagget’ tooling concept. [Courtesy of Sandvik Coromant] . Modular Tooling...
Ngày tải lên: 05/08/2014, 21:20
Modular Tooling and Tool Management Part 2 ppsx
... it Figure 123. Modular tooling ‘capto’ with tool security and precision location via face and lobed taper contact. [Courtesy of Seco Tools] . Modular Tooling and Tool Management ... concept. Together and employing these stated design crite- ria, the following repeatability for the KM modular tooling concept was obtainable: Modular Tooling and Tool Ma...
Ngày tải lên: 05/08/2014, 21:20
Modular Tooling and Tool Management Part 3 ppt
... 131. Tooling and xturing must be precisely controlled at the ‘focal-point’ of kit build-up/replenishment – at the tool preparation area. [Courtesy of Sandvik Coromant] . Modular Tooling and Tool ... for security reasons). A typical tool le must contain all the information rel- Modular Tooling and Tool Management Figure 127. HSK high-speed modular tooling,...
Ngày tải lên: 05/08/2014, 21:20
Modular Tooling and Tool Management Part 5 doc
... optical tool presetting machine. [Courtesy of E. Zoller GmbH & Co. KG] . Modular Tooling and Tool Management Figure 136. Optical tool presetting machine for sophisticated tool management ... mill, then it will cut Modular Tooling and Tool Management storage magazine. e latest tool presetting machines equipped with a full suite of tool management...
Ngày tải lên: 05/08/2014, 21:20
Modular Tooling and Tool Management Part 6 pps
... Figure 142 . An integrated tool and data management system – for complete tooling deployment. [Courtesy of Susta – Tool Handling] . Modular Tooling and Tool Management Figure 141 . Presetting ... [Shrink-t Tooling] . Cutting Tool Eng’g., 34 38, Sept. 2000. Side and Face milling – Application Guide. Sandvik Coro- mant Pub., 1996. Sprow, E. High-speed Spindles for...
Ngày tải lên: 05/08/2014, 21:20
modular tooling and tool management 29 pot
... employing modular quick-change tooling on a turning centre, via the ‘intelligent/ tagget’ tooling concept. [Courtesy of Sandvik Coromant] . Modular Tooling and Tool Management vital and helpful tooling ... taper. Modular Tooling and Tool Management Figure 136. Optical tool presetting machine for sophisticated tool management control. [Courtesy of E....
Ngày tải lên: 27/06/2014, 23:20
Energy Technology and Management Part 4 pdf
... 69 buses, 7 laterals and 5 tie-lines (looping branches), as shown in Fig. 11. The current carrying capacity of branch No.1-9 is 40 0 A, No. 46 -49 and No. 52- 64 are 300 A and the other remaining ... neighborhood solutions 1 and 2. The moves to solutions 1 and 2 give a power loss of 676.63 kW and 48 3.87 kW, respectively. The same process Energy Technology and Managem...
Ngày tải lên: 19/06/2014, 10:20
Tài liệu Teaching and learning english part 4 pdf
... modes of instruction, Teacher as facilitator AKTIVITAS METODE ICT tools (Hypermedia, Database, Reference tools, Intelligent tools, Microworld, Multimedia, Networking, Distance Learning application, ... modes of instruction, Teacher as facilitator AKTIVITAS METODE ICT tools (Hypermedia, Database, Reference tools, Intelligent tools, Microworld, Multimedia, Networking, Distance Learning applic...
Ngày tải lên: 26/01/2014, 17:20
Thermodynamics Interaction Studies Solids, Liquids and Gases 2011 Part 4 pdf
... 90.5 5 .4 GACoxN 816 0.35 267 52 .4 73.7 393 48 .6 3 .4 GACoxN723 903 0.32 95.3 60.2 112 268 103 7.9 GACoxN1023 935 0.37 2.36 10.2 47 .9 60.5 266 8.2 GAC1173 876 0.35 0.00 11.5 34. 9 46 .4 278 8.9 ... Koch W. and Friedlander S. K. (1990) ，The effect of particle coalescence on the surface area of a coagulation aerosol, Journal of Colloid and Interface Science, 140 -2, 41 9....
Ngày tải lên: 19/06/2014, 11:20