Machinery Components Maintenance And Repair Episode 1 Part 7 ppt

... and has been studied over many years, by Dawihl (19 41) , Trent (19 52), Trigger and Chao (19 56), Takeyama and Murata (19 63), Gregory (19 65), Cook (19 73 ), Uehara (19 76 ), Narutaki and Yamane (19 76 ), ... speed 12 6 Tool damage 0 5 10 15 0 5 10 15 0 0 .1 0.2 0.3 0.4 0 20 40 60 80 Real cutting time (min) Real cutting time (min) 15 0 m min -1 150 m min -1 236 m min...

Ngày tải lên: 21/07/2014, 17:20

... al., 19 52; Zorev, 19 66; Usui et al., 19 78 ; Usui and Hirota, 19 78 ; Arsecularatne et al., 19 95). This section introduces the further Non-orthogonal (three-dimensional) machining 17 7 Childs Part ... (three-dimensional) machining 18 7 Childs Part 2 28:3:2000 3 :13 pm Page 18 7 18 2 Advances in mechanics (b) (c) Fig. 6 .15 continued Childs Part 2 28:3:2000 3 :13 p...

Ngày tải lên: 21/07/2014, 17:20

... face. Annals CIRP 19 (1) , 395–398. References 15 7 Fig. 5.24 Relation between flank wear VB and amplitude of AE signal, after Miwa et al. (19 81) Childs Part 2 28:3:2000 3 :11 pm Page 15 7 6 Advances ... mild steels, after (a) Palmer and Oxley (19 59), and (b) Roth and Oxley (19 72 ) Childs Part 2 28:3:2000 3 :12 pm Page 16 9 Harris, A., Hastings, W. F. and Mathew,...

Ngày tải lên: 21/07/2014, 17:20

... Mech. Eng., Vol 17 2, 19 58, pp 87 -11 2. 4. Gregory, R.W., Harris, S.L. and Munro, R.G., 'Dynamic behaviour of spur gears.' Proc. Inst. Mech. Eng., Vol 17 8, 19 63-64, Part I, ... in 19 70 , Sept, pp 11 1 -12 1. 8. Furley, A.J.D., Jeffries, J.A. and Smith, J.D., 'Drive Trains in Printing Machines', Inst. Mech. Eng. Conference,...

Ngày tải lên: 05/08/2014, 09:20

... Mech. Eng., Vol 17 2, 19 58, pp 87 -11 2. 4. Gregory, R.W., Harris, S.L. and Munro, R.G., 'Dynamic behaviour of spur gears.' Proc. Inst. Mech. Eng., Vol 17 8, 19 63-64, Part I, ... in 19 70 , Sept, pp 11 1 -12 1. 8. Furley, A.J.D., Jeffries, J.A. and Smith, J.D., 'Drive Trains in Printing Machines', Inst. Mech. Eng. Conference,...

Ngày tải lên: 05/08/2014, 09:20

... CH8023, Zurich, Switzerland. 3. Harris, S.L., 'Dynamic loads on the teeth of spur gears. 1 Proc. Inst. Mech. Eng., Vol 17 2, 19 58, pp 87 -11 2. 4. Niemann, G. and Baethge, J., ... attainable. References 1. Gregory, R.W., Harris, S.L. and Munro, R.G., 'Dynamic behaviour of spur gears.' Proc. Inst. Mech. Eng., Vol 17 8, 19 63-64, Part...

Ngày tải lên: 05/08/2014, 09:20

... CH8023, Zurich, Switzerland. 3. Harris, S.L., 'Dynamic loads on the teeth of spur gears. 1 Proc. Inst. Mech. Eng., Vol 17 2, 19 58, pp 87 -11 2. 4. Niemann, G. and Baethge, J., ... attainable. References 1. Gregory, R.W., Harris, S.L. and Munro, R.G., 'Dynamic behaviour of spur gears.' Proc. Inst. Mech. Eng., Vol 17 8, 19 63-64, Part...

Ngày tải lên: 05/08/2014, 09:20

... that: clamp bolt accelerometer clamp bolt accelerometer Fig 7. 8 Torsional accelerometer arrangement. T. £. Measurement 10 7 Table 1 - Encoder parameters Dia. mm Mass kg 17 0 2.8 200 3.3 11 0 0 .7 11 0 0.8 58 0.25 58 0.25 36.5 0 .1 36.5 0 .1 Shaft type Solid 14 ... under 0 .1 sec [6]. 1 sees 0 arc - 1 1 revolution Fig 7 .12 Typical error curve for an encode...

Ngày tải lên: 05/08/2014, 09:20

... Measurement 10 7 Table 1 - Encoder parameters Dia. mm Mass kg 17 0 2.8 200 3.3 11 0 0 .7 11 0 0.8 58 0.25 58 0.25 36.5 0 .1 36.5 0 .1 Shaft type Solid 14 <j> 60 mm bore Solid 10 <t> 20mm bore 12 ... mm bore Solid 10 <j> Solid 4<J> 6 mm bore Accuracy Sec arc 1 1 ±5 ±5 13 13 18 18 No of lines typically 36000 36000 18 000 18 000 5000...

Ngày tải lên: 05/08/2014, 09:20

... -1 27 Electroless Plating 27 .1 Introduction 27- 1 27. 2 Plating Systems 27- 2 27. 3 Electroless Plating Solutions 27- 3 27. 4 Practical Applications 27- 4 27. 5 27. 6 ... of Plating Solutions 27- 7 27. 7 Electroless Plating 27- 7 27. 8 Properties of Chemically Deposited Metal Coatings 27- 10 References 27- 11...

Ngày tải lên: 21/07/2014, 15:20