Geometric Dimensioning and Tolerancing for Mechanical Design Part 14 pot

... sketch (cartoon gage), 236 Geometric Characteristic Symbols, 18 Geometric controls to refine datum features, 229, 232, 235 Geometric Dimensioning and Tolerancing, 2 Geometric form, 69 Graphic analysis, ... positional tolerancing, 135 Composite profile, 195 Conical taper, 28 Controlled radius symbol (CR), 28 Coordinate conversion diagram, 251 Coordinate conversion table, 252 Coordi...

Ngày tải lên: 05/08/2014, 09:20

... to Geometric Dimensioning and Tolerancing P1: PBU MHBD031-02 MHBD031-Cogorno-v6.cls April 8, 2006 18:6 Chapter 2 Dimensioning and Tolerancing Fundamentals Many people know how to design parts and ... given at the website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU MHBD031-02 MHBD031-Cogorno-v6.cls April 8, 2006 18:6 Dimension...

Ngày tải lên: 05/08/2014, 09:20

... specify both maximum height and direction by drawing and dimensioning a thick chain line next to an extension of the centerline. The chain line is the MMC height of the mating part and located on the ... .013 4.000 .012 .013 . 014 Summary  The floating fastener formula is: T = H − F or H = F + T  The fixed fastener formula is: t 1 + t 2 = H − F or H = F + t 1 + t 2  The LMC cleara...

Ngày tải lên: 05/08/2014, 09:20

... website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU MHBD031 -14 MHBD031-Cogorno-v6.cls April 11, 2006 21:50 Chapter 14 A Strategy for Tolerancing Parts When tolerancing a part, ... a part. Some designers believe that parts designed with a solid modeling CAD program do not require tolerancing. A note in the Dimen- sioning and Tole...

Ngày tải lên: 05/08/2014, 09:20

... website. A Strategy for Tolerancing Parts P1: PBU MHBD031 -14 MHBD031-Cogorno-v6.cls April 11, 2006 21:50 A Strategy for Tolerancing Parts 243 14. Tolerance the .500-inch clearance holes for .500-inch ... Strategy for Tolerancing Parts P1: PBU MHBD031 -14 MHBD031-Cogorno-v6.cls April 11, 2006 21:50 A Strategy for Tolerancing Parts 233 8X Ø .500 540 Figure 14- 10 A zero...

Ngày tải lên: 05/08/2014, 09:20

... Characteristic Symbols, 18 Geometric controls to refine datum features, 229, 232, 235 Geometric Dimensioning and Tolerancing, 2 Geometric form, 69 Graphic analysis, 207 Immobilization of a part, 48 Implied ... 55 Fixed and double fixed fasteners, 128 Fixed fastener formula, 129 Flatness, 69 Unit flatness, 71 253 Copyright © 2006 by Gene R. Cogorno. Click here for terms of use. 2...

Ngày tải lên: 05/08/2014, 09:20

... website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design Contents Preface ix Acknowledgments xi Chapter 1. Introduction to Geometric Dimensioning and Tolerancing 1 Chapter ... 10.1036/00 7146 0705 GeometricDimensioning andTolerancingfor MechanicalDesign x Preface To optimize the learning process an to drive the information into long-term memory, rev...

Ngày tải lên: 05/08/2014, 09:20

... website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design Contents Preface ix Acknowledgments xi Chapter 1. Introduction to Geometric Dimensioning and Tolerancing 1 Chapter ... April 8, 2006 17:58 Chapter 1 Introduction to Geometric Dimensioning and Tolerancing For many in the manufacturing sector, geometric dimensioning and toleranc...

Ngày tải lên: 05/08/2014, 09:20

... website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU MHBD031-02 MHBD031-Cogorno-v6.cls April 8, 2006 18:6 16 Chapter Two 5. A applies where centerlines and lines representing ... either in degrees and decimal parts of a degree or in degrees, minutes, and seconds.  There are two types of direct tolerancing methods, limit dimensioning...

Ngày tải lên: 05/08/2014, 09:20

... Dimension is a numerical value without a tolerance, used only for general information. It is additional information and may not be used for manufacturing or inspection. The reference dimension is ... government standards and are not controlled by Rule #1. Stock is used as is, unless otherwise specified by a geometric tolerance or note. Rule #1 does not apply to parts that are flexible...

Ngày tải lên: 05/08/2014, 09:20