Geometric Dimensioning and Tolerancing for Mechanical Design Part 10 ppsx

... given at the website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU MHBD031 -10 MHBD031-Cogorno-v5.cls April 11, 2006 23:3 Concentricity and Symmetry 173  The concentricity ... Concentricity is appropriately used for large, expensive parts that must have a small coax- ial tolerance for balance but need not have the same small tolerance fo...

Ngày tải lên: 05/08/2014, 09:20

... dimensioning a part. Figure 4-4 shows a part with four holes. The designer selected the back of the part as the primary datum, datum A, because the back of the part mates with another part, and the ... Part Parts are thought to have six degrees of freedom, three degrees of translational freedom, and three degrees of rotational freedom. A part can move back and forth in the...

Ngày tải lên: 05/08/2014, 09:20

... Use as given at the website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU Chapter08 MHBD031-Cogorno-v6.cls April 18, 2006 15 :10 C .50 1.00 A .50 Unless Otherwise ... head in a countersunk hole and in a threaded hole at the other end is called what? 6. The formula for fixed fasteners is 7. The tolerance for both the threaded hole and the...

Ngày tải lên: 05/08/2014, 09:20

... website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU MHBD031 -10 MHBD031-Cogorno-v5.cls April 11, 2006 23:3 174 Chapter Ten 8. To reject parts and to inspect features, ... of Use as given at the website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU MHBD031-11 MHBD031-Cogorno-v6.cls April 10, 200...

Ngày tải lên: 05/08/2014, 09:20

... website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design Contents Preface ix Acknowledgments xi Chapter 1. Introduction to Geometric Dimensioning and Tolerancing 1 Chapter ... DOI: 10. 1036/0071460705 GeometricDimensioning andTolerancingfor MechanicalDesign x Preface To optimize the learning process an to drive the information into long-term memor...

Ngày tải lên: 05/08/2014, 09:20

... website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design Contents Preface ix Acknowledgments xi Chapter 1. Introduction to Geometric Dimensioning and Tolerancing 1 Chapter ... April 8, 2006 17:58 Chapter 1 Introduction to Geometric Dimensioning and Tolerancing For many in the manufacturing sector, geometric dimensioning and toleranc...

Ngày tải lên: 05/08/2014, 09:20

... website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU MHBD031-02 MHBD031-Cogorno-v6.cls April 8, 2006 18:6 Dimensioning and Tolerancing Fundamentals 11 44.72° 25° 10& apos; ... to Geometric Dimensioning and Tolerancing P1: PBU MHBD031-02 MHBD031-Cogorno-v6.cls April 8, 2006 18:6 Chapter 2 Dimensioning and Tolerancing Fundamen...

Ngày tải lên: 05/08/2014, 09:20

... . 510 .505 .005 .005 . 010 External Feature (Pin) MMC . 510 . 510 .000 .005 .005 .509 . 510 .001 .005 .006 .508 . 510 .002 .005 .007 .507 . 510 .003 .005 .008 .506 . 510 .004 .005 .009 LMC .505 . 510 ... website. Dimensioning and Tolerancing Fundamentals P1: PBU introduction1 MHBD031-Cogorno-v6.cls April 8, 2006 17:58 Introduction to Geometric Dimensioning and Toleranci...

Ngày tải lên: 05/08/2014, 09:20

... of Tolerance Form Profile Symbol Geometric Characteristics Figure 3-23 Geometric characteristic symbols. 9. Write the names and geometric characteristic symbols where indicated in Fig. 3-23. 10. The ... government standards and are not controlled by Rule #1. Stock is used as is, unless otherwise specified by a geometric tolerance or note. Rule #1 does not apply to parts that are...

Ngày tải lên: 05/08/2014, 09:20

... thickness of 1. 010 for the rectangular part and a diameter of 1. 010 for the cylindrical part. Since the MMC of 1.020 minus the actual size of 1. 010 is the automatic Rule #1 form tolerance of . 010, a straightness ... of Use as given at the website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU MHBD031-04 MHBD031-Cogorno-v6.cls April...

Ngày tải lên: 05/08/2014, 09:20